Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello!
Im trying to change my application. Right now everything works with bonding. DFU and reading and writing characteristics. We have noticed a lot of clients unpair...
Hi all!
I'm trying to run the BLE light switch example on the nRF52833 development board using Segger. I get the following error whenever I try to build the client. This...
sorry where i can find the document/spec for the API that we can use to comunicate with LTE stack L3 . Using Zephyr ? threre are some examples that can help me ?
Best Regards...
Hello everybody, I have to develop an embedded system to acquire and process data. I will be using 2 custom PCBs based on nRF52832: 1- Sensor board: very low power consumption...
Hi Nordic, Please, I am doing a design with nRF52840 and would like to be clear on a few points. Attached is the electrical diagram .
Point 1 For the power supply I am using...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using the RNG functionality with CC310 Library.
When we call this "CRYS_RND_GenerateVector...
Given a 3rd party BLE device (for example a fitness) watch, would it be possible to connect to it using the nRF52 DK and conduct a DFU on it? If so, is there any documentation...
Hi,
I am trying to nrfutil to execute dfu over BLE using nrf52 dk and nrfutil. I have no problems when I try to use nrf_connect mobile app, but I want to use nrfutil desktop...
I want to write my application logs to the flash. I am following this tutorial which is for nrf52: https://jimmywongiot.com/2020/02/24/print-log-flash-log-crash-log-on-nordic...
I want to change the GPIO settings for the pin P1.08 but in the register description (nRF52840_PS_v1.2.pdf) there are only the names and offsets for the pins from P0.00 to...
I've been looking for a DC Motor controller example (for nRF52840) but without luck. Some other users have referred to such an example so I figured it should exist.
Anyone...
I am using SPIM4 with easyDMA in list mode to read a set of registers from an SPI device, and everything seemed to work great until I attempted to use the double buffered...
For some reason I can no longer compile any Zigbee examples.
The errors I am getting are below.
I have no idea what the issue is and I can't find any resources to help...
Dear sirs,
Here we've faced with the issue about logs output, could you please help?
We need to use two CDC_ACM devices on the board: one for shell and printk() output...
Hi!
I'm developing a peripheral device using nrf52840 to communicate with our android developed app. I'm testing the latency between connections of device. the configurations...
