I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hello all,
I am having a problem to get SAADC to work with low power. I am using custom board with chip NRF52811, SDK 16.0.0.
I had turned on the SAADC_CONFIG_LP_MODE...
Hello Everyone,
I am using my custom board with nrf52832 SoC and developing my application firmware with sdk15.2 & softdevice v6.1.0.
In my application code, BLE scanning...
Hi,
We were trying out the LTE RX/TX test using the AT%XREFTEST command and undestood that for LTE RX testing ,an external signal generator is required. Is there any way...
Hello
I would like to know if there is a capability of a truly secured boot with the nRF53, starting with a secure bootloader in some locked or immutable memory - i.e. secure...
Hi team
I did follow the getting started assistant to set up software tools and clone sdk ncs 1.3.0.
Verified successfully at getting started assistant, too.
But, when...
Hi
I have some issues with nRF52810.
I am trying to use SPI as a Master on a custom board. I saw here that nRF52810 does not support legacy SPI : https://devzone.nordicsemi...
Hello,
We are adding BLE scanning to an ANT product.
We have been using SDK 10.0.0 from the beginning, so we use the Example below.
SDK 10.0.0.0\examples\ble_central...
Hi Supportor
I have two board, if I didn't set the gain, which used default of SDK, one board output value is 0x2f5, another output ADC value is 0x266.
I set the gain...
Hello,
I'm having issues with what I believe are interrupts, if I use the bootloader.
I'll give a brief description of the issue I faced, and then I'll state how to reproduce...
Hello,
Is there any documentation available that specifies what version of nrfutil is required to create DFU packages which are compatible with a SDK and/or soft device...
Hi
I am using NRF52 with 512KB flash, and with SDK15.2
I am not using DFU
I tried to protect the program flash pages using "sd_flash_protect".
I tried to protect pages...
Hi everyone,
Currently I'm using Android Nrf Mesh Library 2.4.1 for provisioning device into network.
I face the issue which can not be found why to fix this error.
...
I cannot set CONFIG_POWER_OPTIMIZATION_ENABLE to yes in the master branch. It leads to deadlock in at_cmd_write() because that ends up getting executed in the socket_thread...
I copied the slm application into a directory outside the SDK (e.g. C:\temp\slmapp) and I launched a command prompt from the nRF Connect's tool chain manager. Then I navigated...
