I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
A new library/toolkit has been built that allows us to invoke the services of an nRF24L01 from a Java environment. Documentation and links to the Github project can be found...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
Hi Devzone:
I am using P0.00 as SDA and P0.01 as SCL on nRF52833, And I got waveforms like below when I am doing I2C transactions:
the red waveform is SDA and the green...
Hello,
I slightly modified examples\multiprotocol\experimental\ble_zigbee_dynamic_color_light_bulb_thingy so that it can receive changes in the color temperature attribute...
currently i am doing my master Thesis in Bluetooth low Energy. I am searching for BLE Transceiver for Evaluation Purpose. I have a development board S32 from NXP and would...
Hi,
I want to create a Thread border router and am following the instructions from the infocenter.
In the hardware requirements, it is mentioned that the image needs...
Hi Team,
We are using the nrf52830 SOC for our application. In data sheet mentioned that it supports AES-128 bit Hardware engines (ECB,CCM, AAR). How to enable and use these...
Hi guys
I am trying to load a firmware to a Minew's nrf51822 Module using a JLink V8 programmer tool. So far , I can see the chip with the Jlink console:
sudo JLinkExe...
Hi all,
We had implemented Nordic QSPI using "nrf_drv_qspi_write" and "nrf_drv_qspi_read" operation , however I am seeing for page to write in flash of 4096 bytes with 512...
Hi,
During our development, we observed that when BLE central and peripheral devices are communicating, then often central device will not receive data from peripheral device...
mcumgr seems to not like the hex files in mfwnrf9160120.zip, and the NRF programmer can't be plugged into anything automated such as CI, and I'm also running into https:/...
Hi!
This is what I'm using:
-SoftDevice S113 v7.0.1
-SDK v17.0.0.0
-SES v4.52c
-nRF52840
I've created a custom buttonless uart bootloader based on the "secure_bootloader_uart...
So with my NRF52840 board I am trying to use the cc310 backend in zephyr. My project did work until I recently tried to upgrade to ncs v 1.3.0 . The issue was that the build...
Hello, guys!
We are currently developing our firmware with nRF9160-DK and nRF Connect SDK v1.3.0. Among the other things, we need to communicate with the ultrasonic sensor...
I am working in nRF52840 chip with SDK 15.3.0 and softdevice s140. I am looking to automate third party BLE peripheral device, this device is designed to connect with smart...
Hi All,
I have integrated DFU service into my application. I am successfully able to use OAD so far. Today I have added a piece of code to my application. So, my binary...
While doing power profiling on Adafruit's nRF52 Arduino port, I have noticed that when using delay(500), the CPU power consumption goes up about 1ms before actually returning...
