Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
The documentation for this function states the following:
This function initiates or resumes a
Primary Service discovery procedure,
starting from the supplied handle...
kindly check this thread at first
my question is when I tried to power off the system using sd_power_off(); then waked up the system then try to connect, it requests to...
I have written an iOS application that is connecting to the BLE UART example (...\nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_uart) running on an nRF51 DK. I am...
If I understand it right, in java you cannot define a value as unsigned int. So the MSB of a Byte will decide, if the value is positive or negative.
But I have to use all...
I am trying to use the nRF51822 to capture all Bluetooth Low Energy packets on a channel. In it's final application environment the chip will have to fulfill several functions...
I performed flash read using nrfjprog --readcode . here the snipped of the output file
:020000040000FA
:10000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF00
:10001000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF0...
Both nrf51 & nrf52 SoftDevice specs say that this can be done:
infocenter.nordicsemi.com/index.jsp
infocenter.nordicsemi.com/index.jsp
There have been a couple of...
So, I am having a nRF51822 application that I used to upload via wired interface. Now I want my application to support so called DFU over BTLE, enabling software upload from...
Hello,
I'm trying to use nRF51 as bluetooth communication module for LPC1769 communicating over SPI, so I use connectivity firmware in nRF51 and now I'm trying to access...
Lets just stick to GPIO
I am trying to initialize multiple input buttons and multiple output LEDS.
I am trying to glow the LEDS with corresponding buttons...
Hello,
I need to know does nordic S120 stack gives the RSSI value on receiving data from peripheral? Currently I am able to get the peripheral RSSI on peripheral device...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
The Nordic UART code was built for the UARTE using the following definitions:
#define UART0_CONFIG_USE_EASY_DMA true
#define UART_EASY_DMA_SUPPORT 1
#define UART_LEGACY_SUPPORT...
I add my own codes in nRF51-ble-bcast-mesh-sdk-8-support project,
then I find that if device_flash_init() is compile to this project,
the program cannot finish rbc_mesh_init...
