Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
I am trying to set up an environment based on CMSIS Packs. However, when using some components from nRF_Libraries, these lines get added to RTE_Components.h:
#define GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I am working on nrf51 iot sdk. I have created a IPv6 tunnel in HE and is able to ping the gateway as follows:
root@raspberrypi:/home/pi# ping6 2001:xxx:18:xxx::1
PING...
Hi,
I already used the sd_ble_uuid_vs_add for adding my base UUID in the internal table and it return a valid uuid_type (in my specific case it's 0x06).
I need to add...
I am using SDK 9.0.0 and i am having a doubt in bsp.h.In this header file when gone through this part of the code
#if (LEDS_NUMBER > 0) && !defined(BSP_SIMPLE)
#define...
For nrf 51 - DK , I flashed s130_nrf51_1.0.0_API
and then using keil uvision I copied over ble_app_uart_s130_pca_10028 and
tried to compile the code,
The code failed...
Hi,
What is the maximum voltage a level than can be given as an input on a pin on nrf51-dk? I've measured VDD at 2.91V. Is it from VDD-0.3 to VDD? If yes, is there a way...
Now I am trying DFU via BLE, some times I can do it successfully and I can do it as long as i want to, but the other time it shows "Error(0x85) GATT error" message and whatever...
I'm testing the DFU as described in this link developer.nordicsemi.com/.../a00086.html
after reseting in DFU mode, when I start the device discovery, I only get empty packets...
Hello
Quick question. With the nRF51, When in System On mode, should I manually disable peripherals to minimize power even if I'm not using the peripheral in question?...
Can I use RTC1, whitch is used by app_timer for button debounce, ble_conn_params and so on, to realize the time function (hours, minutes, seconds,day, week,month, yea)? And...
Hi, I'm not completely sure if this is a bug but I've been struggling with this for two days so I don't think this is related to my own application code.
The situation...
I tripped over what appears to be a change in the RADIO between nRF51 and nRF52.
For the particular case of issuing a STOP task when the radio is in Rx mode, there is no...
