Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hi All,
I'm using hci interface to scan the ble based beacons.
While scanning hci interface's Rx bytes keep on increasing because beacons are being scanned.
I'm using...
Dear everyone,
My platform is SDK16 and IDE is KEIL V5.25.
I set timer 2 to 104uS to sample a serial data. It isn't UART data, no start bit and stop bit.The start bytes...
1. Using the nRF Connect SDK v1.2.0 development environment, nrf9160 developer, when testing connections to NRF_CLOUD in China, cannot be connected. 2. Please provide the...
1. Optimization is set to 0 flash read and write errors, set to 3 flash read and write correctly? 2. Please tell me what effect the optimization is on flash reading and writing...
Hi .
I am using nRF52840 dk in windows 10 environment.
I want to measure the RF output power of a single nRF52840 using nRF52840 dk.
I succeeded in generating a...
Hello,
On my custom board, on nrf52832, I can can use app_buttons for all usual pins, but not the XL1 (P0.00). I didn't try XL2 (not routed)
Using this pin as input or...
Hello devzone! I am using translation.
I'm trying various things in a continuation of my previous post , but I do have one question.
I set NRF_LOG_ENABLED to 0 at ble_app_blinky...
I've got an nRF52840 dev kit and am building my code using the app_ble_hrs_freertos project as a starting point. I'm building the .elf file, which I load into Ozone to do...
Hello everyone,
I hope that you are all doing well during those hard times...
I am writing a code for a nRF52840. The connection is successfully established with a cycling...
I have the NRF_CCM peripheral setup to encrypt packets on-the-fly. I can verify packets are properly encrypted when the payload size is 27 bytes or smaller. However, anything...
Hi,
I have created a configuration based on usbd_app_uart example where both usbd and softdevice are enabled on my device as soon as the device is turned on. When I transmit...
Hi,
I am developing a simple application that utilizes a light switch client example for NRF52832 with SDK15.0 and Mesh 4.0.
I am facing a problem when using the FDS module...
What could be the reasons that cause DFU Bootloader BLE not working with nRF Connect on PC (while it works with nRF Connect on iOS)? I have had various problem with nRF Connect...
Hello
I am using Seggar Embedded Studio for ARM V3.4 and nRF_SDK 12.3.0. I am trying to understand interrupts and interrupt handlers.
The interrupt request for Watchdog...
