I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
I defined an integer value _ALIGN(4) uint8_t sixteen = 16 and assigned sixteen to a FDS record that is later assigned to the p_data of a custom characteristic. However, when...
I updated to v10.3.0 of the nrfjprog and mergehex tools and I've noticed that the behavior of the page erase command takes far less time when it gets to a certain region of...
Dear All,
I am trying to interface my nRF9160 sensor with the LIS3DH accelerometer.
What I have done so far are the following:
I am trying to use I2C_2
In my prj...
Hello Nordic Support,
I am using nRF9160-DK with the latest module firmware: 1.0.1, board version 0.8.3
I followed the instruction and it only works for tag v0.4.0, I...
Hi devzone!
I connected my flame detector sensor(szh-ek086) which sends data analog value to my nrf52840 DK.
To receive the analog value from sensor I used saadc module...
Hello, I'm trying to set up a series of remote scripts to test functionality on my hardware. The idea being that I can run a handler on the Nordic device and then control...
Hi,
is it possible to read/write the MX25R6435F external SPI NOR flash using Indirect Mode ( https://wiki.segger.com/Programming_External_SPI_Flashes) with Segger JLink...
Dear,
I am doing some range tests with the nRF52840 and saw that the RSSI value of the PCA10059 (USB dongle) can be more than 10dB lower than the one of the PCA10056 ...
Hello everyone, I am trying to implement a blocking wait using the app_timer.
To do this, I am starting a one-shot timer whose callback function sets an initially false...
Maximum current consumption for each of the pins in the respective modules of PWM, TWI-I2C, TWIM-I2C, TWIS-I2C, SAADC, UART, SPIM, TIMER, RADIO-2.4GHz under the operating...
Hi,
I'm trying to run the gps application off the master branch on the thingy91 and it dies like this:
It's built using the Nordic SES on windows.
Any ideas? ...
Hi all,
I am trying to connect to device with specific UUID. I am not sure what have I managed to do, below are some logs from NRF Log.
Did I connect properly?
I am...
Hello,
I am trying to run the mbdedtls example of random number generator shown here https://tls.mbed.org/kb/how-to/add-a-random-generator
I added MBEDTLS_CONFIG_FILE...
when i change the baud rate to 115200 my uart (Rx and TX) are giving me garbage out put.
so what do i need to change in my code(ble_app_uart example) when i have plan...
