I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi,
I'm designing a 2 layer flex PCB with the nRF51822-CFAC WLCSP package and recommended ST BAL-NRF02D3 balun and on-board PCB passive antenna (not ceramic chip antenna...
Hi Friends,
I am using nRF51822(S110 and SDK10.0.0) in my project and I need the chip to be in connectable and advertising mode under peripheral config . I configured the...
Hi,
I have migrated application with freertos (S132 /NRF52 devkit ) from SDK 11.00 to SDK12.00 .
Flashed SD 3.00 and then application ,but Application is not able to boot...
Hi,
Is this the right way of reading the timer value using the capture task. In this code i am trying to read the updated value of counter for every event generated in...
Hello;
I'm developing an application that advertises as a connectable peripheral. As such, it has an ID (think of it like a beacon minor).
I have 2000 of these devices...
Does bootloader example dfu_dual_bank_ble_s132_pca10040 from SDK v11 work with softdevice v3.0?
when I try to run the dfu_dual_bank_ble example with softdevice 3.0, I got...
Hi ,
I have 2 nrf51 dongle compiled with a code which can scan and advertise ibeacon constantly. Whenever receive advertisement packet from each other , they are able to...
Hello,
I'm running one advertiser and one scanner at the same time, and I want to change the data inside the advertise packet, every advertise. Looking at the forum and...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi all, Now I'm working secure bootloader in sdk12 for these I installed the nrfutilv1.5.0 by following nrfutil user guide
link text
while I'm creating .zip files it...
I've seen similar questions posted, but none that match my situation exactly and those solutions did not work for me.
I'm using the pca10040 dev kit, which I connected...
For the radio peripheral, if I use a shorts (shortcut) from END to DISABLED states, is EVENT_END still set? Because I enable an interrupt on EVENT_END, but not on EVENT_DISABLED...
Does anyone know how to remove all Nordic software and clean out all registry keys?
Installed mastercontrolpanel.3.9.0.6.x64.msi and all is working great with the RF Dongle...
Hello together,
i have a question to the uart hardware communication.
I try to send 6 bytes from the nRF51 DK, S130, SDK12 (p0.09 tx) pin to another hardware rx pin.
...
