Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hi,
I have now run most of the YAML test successfully on the Matter TH and while I usually need to restart the TH between runs it seems fairly reliable now. Before sending...
Hi experts, I'm using the example under nrf-bm/samples/bluetooth/ble nus, and I've configured prj.conf, but it's not working.
I've been struggling with this for ages...
I am getting an error trying to get coded phy working with a sysbuild configuration for a nrf5340 custom board:
I am trying to follow the Bluetooth: Peripheral Heart Rate...
Hi,
I am using the nRF5340 for my project.
In the production stage, I am facing an issue: after programming the nRF successfully, when I perform a readback, it shows...
We have a Python script that is using pylink to open an RTT session and send some commands to the Firmware.
We have tried the JLinkRTTClient to send and receive command...
I’m working on reducing power consumption in my application using the LIS2DW12 sensor. I am currently turning off its LDO to cut power during low-power periods.
The problem...
Could you please help with providing terminal plating information for nRF52833? I have it noted as Sn but want to check if that’s matte or bright Tin.
Thank you,
Be...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
I'm wondering if this feature is still supported. I'd like to update some devices from SD 5 to 7.1 I saw an old post and wanted fresh info.
If this is the same, I can...
Our company has previously used the NRF52840, and we know that by modifying the GAP event length (NRF_SDH_BLE_GAP_EVENT_LENGTH), we can enable Bluetooth to transmit multiple...
I am using the SLM project with pppd and cmux for Linux on my custom board. I am able to create CMUX and communicate with the nrf 9151 using the CMUX AT port using my custom...
nRF9151, mfw 2.0.2, NCS 3.1.0
I currently faced issue in calling "lte_lc_power_off" (resulting finally in an blocking call of "nrf_modem_at_printf("AT+CFUN=%d", mode)" ...
We moved a Zephyr project to SDK 3.0.2. After that it is possible to compile it on Mac and Linux machines but on WSL I'm getting an error:
Looks like I miss some environment...
I tried to use west rtt with v3.1.0 and I'm getting the following error:
ERROR: runners.jlink: [Errno 22] Invalid argument
How to reproduce:
Connect J-Link to Thingy...
I have a battery application where I power off areas of the circuit. One of which has my I2C/TWIM peripherals. However, the TWIM controller configured on the nRF52832 is pulling...
