Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi, I already read more threads about this issue. How to program the nRF52840-Dongle. Most threads go to far in details, where my knowledge ends... I just want to run a simple...
I am trying to include software support for the ST LIS2DE12 accelerometer chip which is found in V1.5.0/zephyr/modules/kconfig.st as
config USE_STDC_LISDE12
bool
V1...
Hi,
I'm looking for the source code to the program that came on the Thingy91
I have not been able to find the source anywhere in the documentation
or sample code....
I am trying to port an nRF51 project that runs on the nRF51 DK using Keil to the nRF52840 DK using Segger Embedded Studio. Clearly the best way to start is to take an example...
Hi,
I am using nrf52833 development kit have nRF5_SDK_17.0.2_d674dde with softdevice as s140 when i running the code following error occurs as follows on serial monitor...
Hi
I am facing a problem similar to the one in Case ID228253.
I am using a custom 52810 board and have configured the UART pins on P0.12(Tx) and P0.14(Rx), defined in...
Feeling disappointed while trying to find information on nRF Connect SDK documentation. Let me give this simple example:
Mission: check and ensure that watchdog is enabled...
Having in mind an application that is comprised of two nRF devices (can be two 52833 or 5340 or any combination of these).
One to act as a Central, the other to be Peripheral...
Hello.
I have my application created by referring to "ble_app_buttonless_dfu" example.
When I applied for certification with this application, it was determined that this...
As you know, FDA check issue that is SWETYNTOOTH for all BLE Solutions to apply for medical solutions
So, My customer requested that is checking free from SWETYNTOOTH issue...
Hi,
According to comments above bt_mesh_time_cli_time_set of time_cli.c , if the last parameter is NULL
the function is non blocking:
However, the function returns...
I connected my device over BLE with the computer and currently using Bluetooth LE Console from Nordic. The Console is receiving data and that is good, but I do not know how...
I'm running the radio_test example on an nRF52840, but when I try different modulation duty cycles, it seems to work fine for everything less than 94% however 94% itself starts...
Hi Nordic,
I got the following error when I start nrf connect the first time under MacOS. This log is captured by turning on the Debug console:
Uncaught Error: dlopen...
