Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello,
Conf: custom board, custom firmware, SDK16, SD 7.0.1, NRF 52832
When I configure connectivity advertisement with ble_adv_fast_timeout set to <= 180s the advertisement...
Hi guys,
I have a setup to receive the microphone data from the Thingy 52 on an nrf52840 evaluation board. Currently I recive the 131 audio packages ADPCM encodet. In the...
Hello.
There is nRF52840 and nRF9160 on nRF9160 DK.
here are codes on this two chips:
nRF52840: 1:SoftDevice. 2: BLE APP
nRF9160: 1: Modem & GPS firmware. 2: Bootloader...
Looking at PM_EVT_CONN_SEC_FAILED parameters, i.e.,
re: nRF5 SDK v16.0.0, nRF58233, S113
Looking at the definition for pm_sec_error_code_t: “Possible values are defined...
Hi All,
I've had a product (RunScribe) in the market for some time, running on the nRF52832. This was built on the SDK13.1 / and the S332 v4.0.2 SD. All using Keil. As I...
Hello!
I'm planning to start a project with the nrf52832 chip, I mainly choose this product, because of the low power consumptions and ble.
I would like to start my development...
Hi I am using ncs version 1.5.0 and dk version 1.0.0
I just want to try a simple ping test.Is there any at command are sample code is available to check the network connection...
hello i am using nrf52840 with our customised board with sdk version 15.2 i am trying to achieve maximum distance using coded phy with nrf long range demo as my base i have...
Hello. I tried to run ble_peripheral/ble_app_uart example from the newest SDK (17.2) on my ebyte e73 with nRF52833 onboard, but without success. I used softdevice S140 (tried...
HI,
My application needs to send the data from PC(server) to Nrf52840(client) . The length and type of the data are 2758 bytes and char data type, actually data has been...
Hello !
I allow me to contact to you because I don't go through a building issue.
I'm using SEGGER Embedded studio for ARM V5.40c. My target is N52832. It is not the...
Hi,
I'm working on a nRF52832 project with adc and ble function involved. An external RTC is also included, communicating with MCU via I2C. Everything goes well until I...
Please help to tell the meaning of the "built code" after the NRF51822-QFAA-R7y
There is mention "(H0) of built code. Is there any functional / firmware / hardware difference...
