Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hi
Befor I used nRF51822 to transmit a packet per 5ms, payload length is 12. I can received 200 packets/s, Initialization settings are as follows
Device : nRF51822...
Dear all,
I have been struggling with updating my advertisement data package in SDK15. Using Jimmy Wongs's example ( https://github.com/jimmywong2003/nrf5-modify-device...
Hi,
to initialize the button properly
to trigger the push event on button push and the release event on button release, do I just have to change the button active state...
Hi there,
So I am trying to get a basic mesh setup between multiple Nordic Thingy 52's and no matter what I have tried i keep failing,
I have gone through the forums...
I have an Adafruit Bluefruit Feather nRF53832 board I am considering using and need to change the default serial baudrate from 115200 to 9600.
I am told that I can use the...
Hi:
I am using a shake sensor as an analog input wake-up system. The system is not system off. The analog input signal only generates an event to wake up turn on...
I am using the UART central, integrated with peer manager and UART peripheral application from the SDK 15.3 on our custom hardware. I have 2 centrals running exactly same...
Hello everyone.
I want to familiarize with The Power Profiler Kit. I've installed proper software and been trying to connect to the device but every time I receive the same...
Hello,
I am trying to load the ble_app_hrs example from sdk15 on to my external BMD-350 module, but I cannot seem to discover the module using nRFConnect. I am not using...
SDK:
nRF5_SDK_15.2.0_9412b96
Softdevice:
132_nrf52_6.1.0_softdevice.hex
Hi Sir,
I want add NUS function to ble_app_hrs_rscs_relay sample code and I add...
Hi,
I use a central with 4 peripherals connected with BLE protocol.
On the central, I use the radio notification interrupt. I would like to know which peripheral correspond...
Hi,
I have a problem in my application, i want to add scanning feature, but
When i call sd_ble_gap_scan_start () with these parameters it returns error (0x06) (with...
I am a begineer in Nordic trying to read voltage and current readings from ADC pin. I need to read both values in parallel, with known interval. So I need to use interrupts...
I am trying to use the LTE Sensor Gateway app to send Running Speed and Cadence Service Sample Application data loaded on a nRF52832. I have managed to get this two device...
Hi,
I have a problem with timer and nrfx. I use the migration guide:
So I r emove the old configuration entries related to the nrf_drv_* drivers from my sdk_config.h...
