Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hello,
I ported nordic heart rate example to nuttx. I have peer_manager_init() in my codes.
After programming the device, I can connect and bond when I issue "nrfjprog...
main.c I'm using S120 softdevice with nrf51822, I want to use S120 as central and peripheral devices.
When I received my beacon data then switch to peripheral for advertise...
Hi!
nRF52, SDK13, S132.
I work in central mode and need make
ble_nus_c_rx_notif_enable()
But in the code drivers I only have tx function. In a SDK9 for nRF51 I...
Hello,
I'm trying to prototype an application on the nRf52 DK (PCA10040) using the GCC toolchain. I followed all of the tutorial for setting things up and I can build and...
Hi all,
I tried to load the DFU example for nrf51822 from SDK12.3 on the dongle(PCA10000).
softdevice: S130 2.0.1
I followed the tutorial on: devzone.nordicsemi.com...
What I am trying to accomplish is to establish a connection between an iPhone (device 1) and an NRF52 (device 2), then sniff the data sent between them from a third device...
Hello,
I have designed a custom board with NRF52832 IC which controls vibration motors. And I am turing on vibration motor from n-channel mosfet as shown in the image below...
Hello ,
I'm using ble_app_eddystone example and I would like to stop the advertising and TLM when I press button 2. I able to create a correctly inicialization of button...
we validate the example /ble_centeral/ble_app_multilink_central with NRF_SDH_BLE_TOTAL_LINK_COUNT equals 8. Change the number from 8 up to 15, it still work.
but when the...
in a ble_nus_c_evt_handler().
SDK13, nRF52, S132.
I made connect success. When it done, I send command to peripherial to start discovery. When event came
case BLE_NUS_C_EVT_DISCOVERY_COMPLETE...
Hi, when trying to read a register from a chip using the IIC interface,blocking mode:
uint32_t ms5837_cmd_read(uint8_t *data, uint8_t length, uint8_t register_address)...
On a custom board with an nRF52832, I have some LEDs I'm driving from the pins 9 and 10. One or both of these pins are used for the NFC antenna unless you configure them as...
I am trying to understand the whitelist feature by following the HID Key board peripheral example on S140 v5.0.0.-2_aplha on nRF52840 dev kit. I am using iPhone SE with nRF...
Hi all,
I'm trying to return a write response in nRF sdk but so far no success.
Actually I'm still scratching my head to figure out how characteristic write works exactly...
