I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
I started a new software project on the nRF52832 a couple of weeks ago. I've been using Segger RTT for a lot of debugging with no problem throughout the beginning of the process...
I'm using s110 pheripheral mode in my application. I want it to be in sleep mode and do not advertise untill a central want to connect it. Is it possible, when a central start...
Hey guys!
I face a problem that I have not been able to solve since several days...
I would like to send only one advertising frame every 4 seconds. I do not want to...
I am spending the last 3 days trying to make sure somebody on this plant made it using a mac .
Write a simple program and flash it to the DK. (before we make our own pcb...
Hi,
I'm using nrf51dk board and nrf_log came out correctly on my RTT terminal with built in module. After that I use debug port (P20) to program to my custom module. I've...
Hi,
I have changed in my services so I have added 0x2A05 (service changed) characteristic in my 0x1801 service. But I am not able to read the service.
In didDiscoverServices...
Hi, i'm currently using two NRF52 (1 central and 1 peripheral) using the ble_app_blinky and the ble_app_multilink_central.
I would now like to connect my Android phone...
HI:
I'am an engineer of BLE. And II want PC&Mobile connect my BLE equipment(51822) by type in password like wifi or most of bluetooth Headset.
what should I do. which paragraph...
Hello,
Is there a mechanical specification document for the nRF52 development kit (PCA10040)?
I can extrapolate from the Arduino Uno Rev 3 specification (P1-4 connectors...
hi dear Engineers,
I am affraid to use FLASH to manage PEER data, it is wrong way because of Wr op. limitaion.
Instead of that, EEPROM or FRAM must be used anyway.
How...
Does single bank bootloader in SDK7.1 support ZIP-file ?
I get error REMOTE DFU INVALID CRC ERROR in the end of flashing by nRF Toolbox when I use ZIP.
If I use hex-file...
Hello,
I am trying to implement OTA firmware update using Secure DFU.
SDK - 12.2
Softdevice - s132
Board - PCA10040 (nRF52)
I followed instructions mentioned...
Hello,
I just want to clarity the sd_ecb_block_encrypt() operation cases (S110).
In pp. 23.1.3 of RM (Shared resources) sayed:
The ECB, CCM, and AAR share the same...
Assuming SDK 12.x
For those people that want to integrate the Buttonless DFU service to their app, which uses already one custom base 128bit UUID, please make sure to:...
