In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I download 2 projects
1. Zephyr Project 2.5.99
from install to west flash is Done
2. nRF Connect SDK 1.5.99 manully
from install to SES IDE is Done
3. use nrfconnect361x8664...
Hello,
Conf: custom board, custom firmware, SDK16, SD 7.0.1, NRF 52832
When I configure connectivity advertisement with ble_adv_fast_timeout set to <= 180s the advertisement...
Hi guys,
I have a setup to receive the microphone data from the Thingy 52 on an nrf52840 evaluation board. Currently I recive the 131 audio packages ADPCM encodet. In the...
Hello.
There is nRF52840 and nRF9160 on nRF9160 DK.
here are codes on this two chips:
nRF52840: 1:SoftDevice. 2: BLE APP
nRF9160: 1: Modem & GPS firmware. 2: Bootloader...
Looking at PM_EVT_CONN_SEC_FAILED parameters, i.e.,
re: nRF5 SDK v16.0.0, nRF58233, S113
Looking at the definition for pm_sec_error_code_t: “Possible values are defined...
Hi All,
I've had a product (RunScribe) in the market for some time, running on the nRF52832. This was built on the SDK13.1 / and the S332 v4.0.2 SD. All using Keil. As I...
Hello!
I'm planning to start a project with the nrf52832 chip, I mainly choose this product, because of the low power consumptions and ble.
I would like to start my development...
Hi I am using ncs version 1.5.0 and dk version 1.0.0
I just want to try a simple ping test.Is there any at command are sample code is available to check the network connection...
hello i am using nrf52840 with our customised board with sdk version 15.2 i am trying to achieve maximum distance using coded phy with nrf long range demo as my base i have...
Hello. I tried to run ble_peripheral/ble_app_uart example from the newest SDK (17.2) on my ebyte e73 with nRF52833 onboard, but without success. I used softdevice S140 (tried...
HI,
My application needs to send the data from PC(server) to Nrf52840(client) . The length and type of the data are 2758 bytes and char data type, actually data has been...
Hello !
I allow me to contact to you because I don't go through a building issue.
I'm using SEGGER Embedded studio for ARM V5.40c. My target is N52832. It is not the...
Hi,
I'm working on a nRF52832 project with adc and ble function involved. An external RTC is also included, communicating with MCU via I2C. Everything goes well until I...
