I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Dear All, I am trying to run a simple program that beacons, prints a message to the UART and toggles a pin on a custom nRF52833 based board. I am using softdevice s113 and...
my nrf51822 QFABC1 not working BLE , i used sdk 12.3.0 and uploaded softdevice is s130, and also I upload
I attached my schematics diagram also
please support any mistake...
Hi,
We are writing an application for nrf5340 similar to rpmsg sample with zephyr. We see that the application encounters stack overflow issue when flashed on target...
Hi,
We are trying to synchronize time across 3 nrf5340, where one will be master and the other 2 nrf5340 will have to synchronize their time with the master.
1. All...
I had raised ticket " https://devzone.nordicsemi.com/f/nordic-q-a/63754/nordic-sdk-qspi-driver-call" .
Wanted help for using qspi driver with non blocking mode. I have modified...
Hello, does anyone tried terminated vs unterminated RF switch in AoA / AoD application? According to forum, some people use terminated switch, some don't.
Also, there should...
I've a prototype board which I need to externally program. The prototype board supplies it's own 3v supply to the chip (working fine) via a 5v supply which is current limited...
Hi,
I am using NRF52832 with SDK 17.0.0.
I wanna try to connect multiple devices with only one Android phone.
When I try demo on Samsung galaxy S8, I can connect with...
I am using SDK 14.01 and ble_app_beacon example in that, I want to send updated sensor data in advertising. Using ble_advdata_set() I am able to send the updated data in advertising...
SDK14.0+NRF52832: firstly I init the passkey in the function gap_params_init as above.I want to change the passkey and can save the new passkey to flash, but when I input...
Dear all, I want to measure the current consumption of my application on a nRF52833 DK. On top of that I want to be able to power the device using the VDDH and set the VDD...
Hello,
I am trying to run the A-GPS sample program but am encountering a bit of difficulty with the SUPL code.
I had to modify the LTE connection code to allow access...
Hello,
I am using nRF51422 DK running on SDK v12.3.0. I am migrating the project examples/ble_central/ble_app_uart project from Keil uVision to Segger Embedded Studio using...
Hi,
I am trying to toggle one pin via PPI when receiving event on another pin - code snippet below:
#include <stdbool.h> #include <stdint.h> #include "nrf.h" #include...
Hi,
What is the fast way to stream data from NRF52840
1) Using USB interface and virtual com (CDC)
2) Using UART interface and extenal converter as DTFI
Please Advise...
