I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
i tried add ancs to my project based on s132 ble_app_hrs demo， when i use iphone6 to connect， the uart display as follow，but when i receive a message or a call， the software...
i have an external nrf51422 module, and i can to erase it using nrfgo studio by nrf51 DK, but i can't program it with nrfgo studio , or by keil .
and i can't open the program...
Trying to get the debugger working with Eclipse on SDK 12.2 using the nrf52832. Using the ble_app_hrs example, I can flash the application and the "Nordic HRM" device shows...
Hi guys,
I am experimeting using the experimental_bootloader_secure_serial
example, but I am not having luck with the example code. I tried using the
BLE secure bootloader...
Dear Engineers!
have a questions about the Input circuit of nRF52.
I have to monitor the signal LEVEL from some sensor. The signal can be Positive or Negative current...
Hi,
I have a board with a NRF52 (3rd party board), there is a 32MHz crystal with the correct load capacitors on, but the crystal is outputting 1MHz on a scope (Tektronix...
Hi,
I'd like to output some audio data through i2s. It's quite easy to understand your examples provided on infocenter, however, I can't get my code to work.
Here is...
Hi all, I'm working on sdk11.0.0 and s130 softdevice. In my project I need to take data from sensor board through uart and send to mobile through ble for every 500ms. Sensor...
Hi guys
I want connect nrf51822 (Raytac MDBT40) by my phone(HTC battery one android 4.4.2).
I use softdevice 130(ver.2.0.0) and SDK 11 demo code under KEIL ARM 5.
...
when i run sudo nrfutil dfu serial -pkg my_package.zip -p/dev/ttyACM0 i get the following error:
pc_ble_driver_py.exceptions.NordicSemiException: Failed to send init packet...
Hi
I am working with mbed targetting for ReadbearLab Ble Nano. I am trying to encrypt payload before sendind it with:
include "nrf_ecb.h"
...
int main(void)
{
...
Hi, i'm using keil and i would like to run the fpu_fft example to perform a fft. The example works if I set 128 or 256 as number of input vector data as you can see in the...
I'm using SDK 6 + S110 v7.
Is it possible to use device manager to perform bonding but don't write bond information persistently in flash?
With old bond manager I could...
