hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
When I program the board the COMP and Timers work fine. Upon removing the debugger and resetting the board it also works fine. But if I subsequently power off the board and...
Hello.
I don't know difference of GPIO's input/output direction setting.
There is two register for gpio setting.
DIRSET : Dir set register
PIN_CNF[n] : Configuration...
Hi there,
Is it possible to call SOC library functions before calling sd_softdevice_enable()?
In particular, i want to set up my interrupts with sd_nvic_SetPriority...
We want to use 52832 to control 6 LEDs. it is easy to use 6 IO pins to make them on and off. but we need these LED to blink. so we want to use one PWM module to generate 1...
When using the nrf_drv for spi master there are no problems when compiling. If I switch the SPI configurations to operate as a spi slave the compiler spits out "non-trivial...
Hi All,
I have just started working on interfacing SD card with nrf52 using SDK 12.0. I have to write to SD card at a rate of 84 packets per second and each packet consists...
Hi
I am checking out NRF51822, NRF24LU and NRF24LE1.
Below are my design requirements:
Smaller the size, the better. 7x7mm is OK. prefer smaller.
Lower power...
Hi, Nordic
I have 3 nRF52 devicies, one as Gzll Host, two as Gzll Device.
they use Gzp to pair, when paired, two Gzll Device send payload via different pipe ( 2, 3)...
Hey everyone, I'm trying to use lmt70 with nrf51822. So, first of all, nrf51 has 10-bits ADC, the data sheet of lmt70 is recommended 12-bits of ADC.
I plugged the sensor...
I use nRF51822 (Multiprotocol Bluetooth low energy/2.4 GHz RF System on Chip).To transmit informations with smartphone.
I have to set up a self-certification application...
Dear Nordic.
Is NRF_POWER->GPREGRET register writing in NVMC?
FICR and UICR is saved in flash memory(NVMC) as written by [nRF51_RM_v3.0.pdf].
But, GPREGRET register...
Hi，
I have the following setup
Chip: nrf51822 chip
SoftDevice: S110
Firmware: dtm exmaple.
I use device test Bluetooth certification in korea(RF output from our...
Hi,
I'm new to development using nordic's products. Basically I'm a Hobbyist working on a project of mine, which needs a low cost wireless.
I was looking for a Rf Soc and...
Hi, has anyone used the nrfgo SDK (for the nRF24LE1) with either eclipse or SDCC? We use those platforms already, so it would be great if we could add your SDK to our toolchain...
