I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hi,
I get the ble_app_att_mtu_throughput -example working with the coded PHY between two nRF52840 boards. Very nice, although I did not yet get the coded PHY advertising...
Looking at the ble_nus service, I see that the SoftDevice allows notifications to be more than 20 bytes long:
uint32_t ble_nus_string_send(ble_nus_t * p_nus, uint8_t *...
I'm try to use RTC1 to generate overflow interrupt, but it doesn't trigger interrupt.
void RTC1_IRQHandler(void)
{
// do something
}
main()
{
NRF_RTC1->TASKS_STOP...
Hi,
I'm using s132, sdk 12.1 on nrf52x, my question is about possible race condition when setting the value of a characteristic using sd_ble_gatts_value_set (on peripheral...
Hi,
I am working on a IoT based project with nRF52832 and nRF52840. I am looking for PCB Designers and people who can develop firmware for our project. The firmware development...
Hello, in S110 device's nrf_sdm.h, there is this enum "NRF_CLOCK_LFCLKSRCS" which is defined as:
enum NRF_CLOCK_LFCLKSRCS
{
NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM, /**< LFCLK...
Hi..!
I am trying to ***Receive ACCELEROMETER DATA FROM MPU6050 to PCA10028(NRF51822) AND WANTING TO PRINT IT ONTO UART using KEIL IDE.
Code is getting compiled & getting...
HI.
I want to send data from nRF24L01 + to RF communication and receive it from nRF24LU1 +.
The nRF24L01 + is connected to the STM32. The settings are as follows.
...
Hi, I'm trying to build a bluetooth device that pairs once, and does not have other hosts maliciously or accidentally pair to it (which would create a poor experience for...
Hi,
When i used nrf51822, i remember the s110 define max transmit buffer as 23 Bytes, but now, i am using nrf52832, the max transimit buffer is defined as 158 bytes.
Does...
Hello, I understand this may be a very broad question, but I still need to find as much information as I can.
Give a general answer if you'd like to, or a very specific...
Hi,
I just got the email about SDK13.0 official release. The list of changes in this release include "Secure DFU improvements". What does it mean?
Is Buttonless Secure...
Hi Engineer!
I would like to use DTM mode to test nrf52840 in our pre-samples.
but i did not find any info about that. how to use DTM in this chip ?
thanks you!
