In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hello
i am using Nrf52dk. i have Visualgdb.
i would like to use the Nrf5 IoT sdk in visualGdb.
i have some question. is that Nrf5 IoT sdk will support the SysGcc toolchain...
good time dear Engineers!
faced with a problem of S132 nRF52. ADV data of packet lost.
I compared the RAW data according to screens below:
If I use nRF Connect ...
Hi, Nordic
I see this question: devzone.nordicsemi.com/.../ , I follow it, then I can see log in J-link RTT viewer.
But when it work, I find after some time, the old log...
Hi would like to evaluate the consumption of my pcb in connected mode using a nRF51. For that I use the nordic excel tool : "APM_nRF51822_S110_v3 0c.xlsx".
But I really don...
Hi,
I am trying to save some data in flash by using the Flash data storage.
However, everytime I try to write data to the flash, the module returns this error code:
FDS_ERR_UNALIGNED_ADDR...
Hello,
I'm making bootloader(nrf51822xxAA SDK12.1.0 and SD130 version).
I have some problem in micro-ecc installation.
To install micro-ecc, complete the following...
Hi, I have a problem with DFU OTA.
I use nRF Toolbox's DFU to upload nrf51822 QFAC, most times it works.
However several times, after the app altered "** bytes transferred...
Hi,
I want to generate a 2.048MHz clock on one of the IOs of nRF52832. Could you comment on following questions?
1- Can I generate this frequency (with no load on CPU...
Hello, I work with some ADC 24-bit (HX711) and for getting data from that I need after low level on first gpio pin to fed 26 pulses to that with time period about 1us on second...
Hi,
I am using ble_app_uart_c_S120
How can i support more then 1 bonded connection?
i try:
#define DEVICE_MANAGER_MAX_CONNECTIONS 7
#define DEVICE_MANAGER_MAX_BONDS...
What's the correct settings for nRF51822 CEAAE0 (0x0079) with dfu example in SDK v11 ?
I believe the chip I am using is a 16KB ram 256KB rom version, but not sure 51422 or...
reco_scan_req.PNG
Now i am doing a test of RECO beacon which use a nordic chipset, nrf51822.
But something strange came up to me during the test with Ellisys bluetooth...
Hello,
I know that this question has been asked in the past but I could not find any recent post about this topic, and there have been many updates to the SDK since the...
