I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
I am using sd_power_system_off() to enter System Off. It is my understanding that all peripherals are off in System Off, but that GPIO configuration is retained. I have a...
I have the following code
// Initialize timer module, making it use the scheduler
APP_TIMER_APPSH_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE...
In the ANT Message Protocol doc, section 7.1.1.1, and in example code, the Device Number is treated as a uint16_t and shown as a two byte field in the flagged extended data...
Hi,
Will something interesting happen when the text segment on a nRF51 DK exceeds 64k? I am using Eclipse/gcc for developing, based on the tutorial provided by Nordic....
Hi,
I am developing a program on a Nordic nRF51 DK, using Eclipse/gcc, and am using J-Link RTT for a debug command line interface. This has worked very well for some time...
Hello,
I've been looking a bit into the nRF52 product specification and I was just wondering how powerful EasyDMA is under extreme conditions.
Let's assume the following...
I am currently working on a device using a nRF905. We want to use the device in Region 2 (USA).
This means that we need to use frequency hopping between 902 and 928 Mhz....
Hi,
I'm implementing a simple bootloader which will not use BLE.
Application will transfer the data from mobile devices using BLE and this data will be stored to...
I'm looking for a smart solution to connect my application to different ANT+ sensors and transmit a logfile to a mobilephone via BT (and receive notifications from mobile...
Hi~ Sir:
I test S120 connect with S110 have problem ,test methods are as follows
S120 connect with S110 ,function ok.
S110 Power Off and On, the interval time about...
Hello everybody,
I've been digging through the forum and the documentation for hours now. But to be honest I don't understand the whole timer thing.
I need a simple...
Hello,
while implementing a BLE link layer, I’ve stumbled over a race condition, where I have a problem to find the cause. Maybe someone of you have an idea, on how to...
I am reading data over the duration of 3 seconds on SPI, but while I'm doing that, I need to send that data over RF using microESB library.
I need to make sure the read...
I use the chip nrf51822, However, SDK8.1.0 example ble_app_uart is base on nrf51422, what I need to do? just replace bsp.c ? and which bsp.c file corresponds to the nrf51822...
I'm tring to build a FOTA broadcaster machine using a raspberry-pi with bluez. or any other Linux small linux embedded system.
The idea is that after testing the board...
