Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Hello!
I am facing some strange behaviour using nordics dfu update service on android.
Somtimes after starting the dfu upload the app is not able to connect to the dfu...
Hi,
How to get this done using TWI this temperature sensor's I2C to write 16 bit register, it is sending start after device address then data. I tried as below, but it will...
Hi, I want to be able to send 1bit of data with as low latency as possible, what is the best way of doing this? Can i in some way directly control the low level of the radio...
Hi All,
i am using the below link to flash the bootloader
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/device-firmware-update-dfu-with...
Hello,
I am using Eclips & ARM tool chain for project with BLE functionality. I tried to import this code in Segger embedded IDE but it did not worked. This project is old...
Hello,
I built peripheral_hr_coded sample and looking into the partition manager report (I trucated the output):
What are the s0_pad and s1_pad?
What are the EMPTY_0...
Hello,
I am developing a FreeRTOS project that uses nRF5340 MCU. For the inter processor communication I would like to make use of the RTOS-agnostic RPC library (sdk-nrfxlib...
Hello fellow bit jugglers!
We are developing an application for a nRF52805 on a nRF52-DK board, using NCS.
NCS version: 1.7.1
Zephyr version: 2.6.99-ncs1-1 (commit...
Hi:
I have a BLE HID remote control that needs to be connected to the HID central(nRF52832).My SDK is NCS v1.8.0.
When I try to connect with the HID remote I get the log...
Hello,
I have to make the external flash on the nRF9160DK work with the nRF9160.
From what I understood, the default settings are that the external flash on the board...
I have beacon that broadcast its name with type 09. I cannot get it while scanning of nrf_uart_c (adv_report).
I assume I need to activate scan_req and then parse the response...
I need a constant acquisition time for my SAADC. In my experiements I see jitter in the acquisition time, so I started debugging with PPI to ensure no Interrupts are making...
Hi,
I am trying to enable event length extension on uart example provided on the sdk. I look for information on how to done it and i found links like that:
https://devzone...
Hello，
I am using ncs1.7.1, qspi + mx25r64 external flash ota it works well, but I don't know how to change qspi to spi.
I need your help thanks
I change the parament...
