Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I have been struggling to get the DFU in our own application to work. When starting a DFU from the desktop nRF Connect 3.4.1 it reports an error:
According to the log...
Hi,
We are using nrf52840 development board and segger embedded studio. I am using thread concept here to run another function in parallel to my main function. i want to...
Device: nRF52840, nRF5 SDK16.0, Softdevice: S340 (ANT_s340_nrf52840_6.1.1)
Hello,
As next step to increase usability of our product and adding new features, we have...
I hope someone is able to answer a few question.
I read quite a lot but still some things are still confusing.
If we use e.g. the AMB2621 Module of Würth, is skipping...
Hi,
I am trying learn about IO/ events that can wake-up nRF52833 from lowest power mode.
What qualifies as event that can serve as wake-up source?
Is it possible to...
Dear sir,
Got error while uploading .zip in DfuTarg as "SD version failure". I'm using nRF52840 DK board. I have tried to create .zip by --sd -req 0xB6/0XAE/0xA9. zip get...
I'm curious what the modem does if, upon waking up to service the PSM interval, it fails to connect? Does it go back to "idle" and try again on the next PSM interval or does...
Guys, In a Mesh project, when setting up flash manager:
How do you get the right value of flash_manager_config_t.p_area ?
And where and how is it configured?
Thanks...
Hi ,
I wirte a python script to download FW to nRF52832 custom board, the FW is the merged file with softdevice（s132_nrf52_7.0.1_softdevice.hex）, bootload, bootload settings...
The version used is nrf5_SDK_for_Mesh_v5.0.0_src.
nrf5_SDK_for_Mesh_v5.0.0_src\examples\light_switch\server.
Question 1: I want to turn off mesh broadcasting first,...
Hi
data sheet of the nRF52840 states that the QSPI port pins should be initialized to "high drive".
I've experimented a little bit because I have problems with a Macronix...
I have connected a BM680 sensor on a BL654 (NRF52840) via I2C. I have connected the power to the BME680 on a switchable power rail. I need to power this rail with a GPIO pin...
I am trying to create a test case for in house validation and would like to know how to do so.
Here is what I want to do:
I want to create a boot loader that checks...
Hello,
In nRF5_SDK_17/examples/dfu/secure_bootloader/main.c, the main program starts off with protecting a couple of flash areas:
But how can, after this, an OTA update...
I don’t know what all the XML syntax is, or what program processes the flash_placement.xml file, or what form the output is in, so I don’t know if I have to do exactly what...
