Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi all:
I download nRF51-ble-bcast-mesh from GitHub ,and put this project under below folder
...SDK8.1.0\examples\nRF51-ble-bcast-mesh-master\
compile this example...
I was doing power profiling using the PPK. All was working OK, as far as I went. I disconnected the PPK, and returned to normal debugging with stand-alone DK. Now I can't...
hi,all
S110 NRF51822 SDK8.0.0 server
i want to increase the througout speed,the SDK8.0.0 support changing MTU size?
MTU Can be in 4.0 protocol is modified?
if SDK8.0...
Hello,
I am starting to create a bootloader and I want it to be independant of the SoftDevice. Is there any open source implementation of a flash_write function that I...
Hi
officially for the nrf51 chip, 40 ppm frequency tolerance recommended but I'm not able to find this much of tolerance in digikey.
The only matching crystal digikey...
I am trying to get a NRF HRS central (ble_app_hrs_c) to make a connection to a NRF HRS peripheral (ble_app_hrs). However, the peripheral does not show up whenever the central...
It seems like a really great company, but after exploring and asking , and searching for a good BLE solution, I just can't find a good fit.
So you want a GOOD processor...
What is the Best way to send float over BLE?
Values range between -2.000volt and +2.000Volt (-2000mV / +2000mV)
Do I break it into two uint8_t and manipulate the +/- sign...
I am engineer, and I may be sensitive to user experience, or just a bad engineer but I do not get this.
I read ALL the guides available in the last 5 hours,
this
this...
Hello,
I have just migrated my project from sdk 9 to sdk 12.2....and of course from Device Manager to Peer manager. My initial project which was built off of the sdk 9...
During the webcast earlier this week, we were shown a phone pairing with the nRF52 dev board using NFC.
Is the code used for that NFC demo available as an example project...
Hi,
I am using nRF52832 as the core of my device that works with battery. I have to keep the SoC powered on all the time. When the off push-button is pressed I restart...
I am using a nrf52832 to communicate via UART to a GSM module (AT commands).
I have setup the device with a baud rate of 9600 and using HW flowcontrol. The nrf52 is doing...
i want to communicate nrf52dk with arduino over spi.i want use nrf52dk as a master and ardunio as a slave.kindly refer me some example or code or any thing which s helpful...
