Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi,
I bought the nrf51822 chip itself, and created my own board. Now, can I still download the nRF51 SDK as per nAN-29?
I am stucked with the download page asking for...
Guys
I came over from the Arduino forums, I am searching for a new RF chip to use for a project i am working on but dont know which chip to pick. My application requires...
I want use uart to debug my ble program ,
In the devzone I found this and this to meet my need , but when I conditional compilation UART code into hex, I can not find my...
Hi All,
I am trying to use the HRM_RX sample code with my Linux PC side application. but i am not able to receive any UART RXD interrupt on nRf51422. I checked PC is sending...
We are developing a BTLE perihperal product using nRF51822 chip. But we would like our product can be up-gradable. So we will need a Bootloader (by UART or other interface...
while creating a Makefile for DFU, for BLE DualBank only, I'm getting some odd errors:
../bootloader_util_arm.c:19:1: error: 'at' attribute directive ignored [-Werror=attributes...
SDK v5.1 /v4.4.2
Keil 4.73/Keil 5.1
delay function seems doesn't work well in new version of keil. But I need it to bebug and flash nRF51822 with new keil.Need your help...
I would like to use an nRF8002 in a proximity detection application.
I would like to be able to send a request/command to the device to start a continuous or rapid transmit...
This may be an obvious question, but I wanted to make sure that my assumptions are correct.
The nRF51822 is able to use an external 32kHz crystal oscillator for its low...
In the 51422 Prod Spec v2.0 it states that “high performance RF capacitors” for the X7R decoupling caps should be used.
Is High performance RF equivalent to a “High...
Hi,
I am trying the Direct Test Mode (DTM) function integrated into the nRFgo application. I am using the nAN-34, Dev Kit User guide, and help (F1) in nRFgo as documents...
I use DK usb dongle to catch data from my ble device , but I can only catch the broadcast data . When the ble device is connected to PC ble dongle , I can't catch data any...
I have Olimex Mod-nRF 8001 Module which i bought it from here . It has break out the RDYN,REQN,MISO,MOSI,SCK and reset pins. My question is can i connect RDYN and REQN lines...
