I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
We have a locator-beacon setup based on this https://docs.nordicsemi.com/bundle/ncs-2.9.1/page/nrf/samples/bluetooth/direction_finding_connectionless_tx/README.html running...
I have been facing a persistent Zephyr CMake/Kconfig build failure in my nRF Connect SDK setup.
Environment: Windows, nRF Connect SDK v2.7.0 , Toolchain v2.7.0 , using VS...
Hello Nordic team,
we are using a nRF52820 module in a beacon. After flashing the firmware and connecting via nRF Connect for Mobile, we can read the Service and Characteristic...
Hi,
I'm trying to CONFIG_MCUBOOT_ACTION_HOOKS with mcuboot on a custom board build with an nRF9151. McuBoot works well, but I'd like to use CONFIG_MCUBOOT_ACTION_HOOKS to...
Hi
I use MT8852BE to test nRF54L15-DK ,TX power setting 8dBm but MT8852BE Power(Pavg) show -6.07dBm ,Why is there such a discrepancy in the values?
nRF54L15-DK Setting...
For power cost down, use dts config to set pwm gpio H0D1 as follow:
pwm1_default: pwm1_default { group1 { psels = <NRF_PSEL(PWM_OUT1, 0, 26)>; nordic,drive-mode = <NRF_DRIVE_H0D1...
Hi,
We have defined a FOTA update for a set of devices. Our device SW follows the 'multi-service sample' code for FOTA.
Generally, FOTA works well for devices in a job...
Currently (as far as i can tell) the firmware for the DECT-NR+ mode is mutually exclusive with the LTE firmware, and you cannot mix the two wireless modes as you have to flash...
We use the device shadow "desired" section to send configuration params to the device. The device processes and accepts the params and then returns them in the "reported"...
HI
Based on the nRF54L15 with SDK 3.0.0 and MCUBOOT for OTA updates, I've discovered there's a firmware image compression algorithm available. However, when compiling with...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
Hello,
for some time I didn't have to work on my project that uses nRF Connect SDK but recently I had to work on it again and noticed that I am not able to build my before...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
When running the NRF Connect SDK SoftAP sample, connected stations disconnect at **exactly 5 minutes** (300 seconds) into the session, regardless of activity or configuration...
Hello support,
For our project we have an integration with Memfault for metrics, coredumps and log files.
We are currently developing in NRF 2.7.0 on a nrf9160 chip. ...
