Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
Regarding...
Hi everyone,
I'm new to Nordic development and currently working with a custom board based on the BC40C module (using an nRF5340). I’m facing an issue with the Bluetooth...
I’m working with nRF9151 + Toolchain 2.9.0 and wanted to share my experience & issue while sending ~7kB data over UART. I’ve tried both DMA & FIFO-based approaches — here...
I am designing a wireless sensor pcb with the nRF52840. I am essentially following the Circuit configuration no. 4 schematic for QIAA aQFN73 from the datasheet to a tee (schematic...
Hello,
I have bought a couple of Nordic NRF54L15 DKs, and it seems that the distance measurement toolbox that was compatible with the NRF52 series is not supported in...
We have nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-1 and the same Toolchain, IDE: VSCode + nRF Connect plugin
We need to control the GPIO LEDs from two cores ( P9.00...
Hello, as the 32.768khz PPM of our product is out of the range, so i need to fine tune the C1/C2, now C1 and C2 are 22pF, is it in range? what is the range for C1 and C2,...
So i am currently referring this ticket and from that I get to know that when when setting parameters for create config (HCI_LE_CS_Create_Config) command for channel sounding...
Hi,
I’m currently working with the nRF52840 DK configured as a BLE Central device. The peripheral device is a Flutter-based mobile application acting as a BLE Peripheral...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
I am developing a Bluetooth Low Energy (BLE) application based on Channel Sounding (CS) using the nRF Connect SDK v3.0.2 on ME54BS01 modules from Minew Semiconductor (powered...
Hello DevZone,
Our team has been working on a customized firmware solution that has been flashed onto the nRF52840 DK to meet specific requirements.
We’ve noted that the...
Hi everyone,
I wanted to share an update on the BLE issue I’m experiencing with the BC40C (nRF5340) module on my custom PCB. I initially described the problem in this ,...
