In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Dear DevZone,
I'm trying to use the Seeed CAN BUS Shield V2.0 (MCP2515) with the nRF52840 DK, but the library provided is written for Arduino One.
Do you know if any already...
Hello.
I m looking for libraries wich contains functions/methods (for example how to scan, provision, adding nodes etc. ) and solution how to use them.
I found something...
I am working with nRF 52832 platform and I soldered SB12 and cut SB10 because I wanted to feed from the external power supply and with this situation I can not connect to...
I have been working with the Nrf52840, SDK15.2 and Segger Embedded Studio 4.20a using external GNU 7 2017-q4-major. The project builds without error on the original PC. I...
Hi
How to find out which BLE version is supported for a given Nordic SDK + SoftDevice.
From which version of Nordic SDK is compliant to Bluetooth 4.2 ?
Hello,
This subject is partly a conclusion and partly a question I would like confirmed.
Our scenario is that we would like to fetch flash logs over BLE, but not really...
“EBSHSN” is reset by the RESET pin when the control CPU shifts to sleep mode when the terminal device is stopped. When measuring the current consumption in this state, about...
Hi, nordic.
I've been developing a product with ws2812B.
As I know, ws2812B is needed around 5V to work well.
And I measured voltages on 52 DK board.
VDD pin has...
Hi,
I designed a customer board and defined my own board header file, which is pretty much copied from pca10056.h. One question I encountered is I somehow couldn't toggle...
Hi,
I try to develop a fix that should allow me to use the pc-ble-driver to receive scan responses (see https://devzone.nordicsemi.com/f/nordic-q-a/50082/pc-ble-driver-no...
I have one doubt that why there is elements or models in Bluetooth, it can be simple as sending messages and then translate them into useful work, in this single element and...
hello,
inorder to send a string over ble from a slave to master or master to slave what is to be done??
is there any function for us to pass the string??
I want to understand the meaning of "standard drive, low frequency" GPIO pins. The datasheet mentions to use these pins for frequencies below 10 KHz. Does this limitation...
HI
I have to sending a sequence of 768(96 bytes) bits to program a custom piece of hardware on a single data line. Initially the line is low for 500ns and then each bit...
Hello. I'm testing ESB examples with nrf52832. Want to understand which max speed I can reach with that protocol? Some devzone info says that 1.8mbps can be reached. But among...
