Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
as described here https://devzone.nordicsemi.com/f/nordic-q-a/37056/supervision-timeout-and-unplanned-disconnect our device has a hard current limit of 2mA.
Problem...
I have a trouble in my project.After flashing softdeivc,I flashed my application,but adversting is not work immediately, then a turn off the hardware and wait some second...
Hi:
I am developing my project based on ble_app_uart example. The development bench is SDK13.0, the chip is nRF52832.
One problem I have now is that: I configure Pin12...
When using FreeRTOS, external GPIOTE interrupts do not work.
And just how correctly to use the NFC with FreeRTOS?
In examples NFC use app_scheduler for events handling...
Hi
I've done a few attempts in the last years to implement a reliable reception by using the UARTE. In the past we used the UART periphery from the nRF51, but we thought...
Hi Everyone
I have the following issue in my application code.
If i configure a pin as an input pin , i am not able to run the ble init function in which it advertises...
Hi team ,
i am vishal working for VVDN Tech .
we are going to use 10k parts of nRF52840in our project.
so we need step file of that.
Awaiting your soonest response...
Hi,
I am trying ble_app_uart example of SDK 15.
When I do not connect Uart port (TX, RX) to other peripheral, I get fatal error (log via RTT).
```
0> <error> app...
Hello! I am now using nrf52832 sdk14.2 development, as a slave device, need to be bound to the phone, I now want to know the maximum number of allowed bindings and the current...
Hi support team,
I'm using nrf52840 and SDK 15.0. I need to add buttonless dfu service to my application so that my device could be able to upgrade firmware OTA.
However...
When flashing SoftDevice S130 v2.0.1 with nRFGo Studio ( JLinkARM.dll 5.12f ) and softdevice protection enabled, the UICR.CLENR0 is written with value 0x00B00100 (~11M Bytes...
Hi
I would like to create bin file that contains: softdevice, bootloader, maIn application.
To do so i have programmed sofdevice and bootloader via JLink:
r erase loadfile...
Hi,
we are using mesh SDK 2.1.1 over nRF52832. In that, we had developed our custom bootloader, which was based on UART interrupt to receive commands & data from the host...
Hi,
I am running into a problem on PAC10056, please help, pca10065 used to work fine, don't know what caused, I cannot run or debug code on it through SEGGER, I got
...
