Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hello
is this possible to reset the timer.
for example i set the timer for 10 Second.
when he reach up to 5 second then i would like to reset the timer.
i found no function...
Hi,
I just noticed that my PTX and PRX projects use different assemblers and linkers -- not sure why. I got the sample projects from Nordic. What's the difference between...
I built my project on ble_app_uart peripheral example from SDK 12.2 and have added a display (Sharp LS044Q7DH01) using nRF52 as a SPI master to communicate. I think I have...
I have used NRF52840 and SDK 13.0.0. Module SPIM.
Library does not support buffer size more then 8 bit.
But I try write to register TXD.MAXCNT and I can't write value more...
Hi
I'm interfacing MMA8452Q with nrf51822 using TWI all read-write function working fine but when I try to read acceleration data nrf_drv_twi_rx & nrf_drv_twi_tx function...
I am porting our sdk 8 based firmware for the sdk 11. Now the code crashes at the code below:
err_code = sd_ble_gap_device_name_set(&sec_mode,
(const uint8_t *)name,...
We followed the instructions for the beacon example for nrf 52 dk.
Multiple attempts to change and reset the board, there was no change in the ad packet.
Can someone...
I'm using the nRF52832 chip without an external crystal. I configured it to use the internal RC with:
nrf_clock_lf_cfg_t clock_lf_cfg;
clock_lf_cfg.source = NRF_CLOCK_LF_SRC_RC;...
Hi,
I have tested ble_app_hids_keyboard for using whitelist.I find that this example is bond+whitelist. If bonded, the peer address will be added into whitelist. But when...
Hi,
I test Whitelist function in the example ble_app_hids_keyboard_pca10040_s132 using SDK12.2.0.
I donnot understand the code in "case BLE_ADV_EVT_WHITELIST_REQUEST:" located...
Hi all,
I have some problems with GPIO Interrupts.
I'm using nrf52832, s132 and sdk 12.2
The error is totally random so I don't know why is generated. The case is...
Hi,
We are using the Secure DFU from SDK 12.2, with SD132 3.1.0, on a PCA10040.
As a DFU controller, we use a PCA10031 with a SD130 2.0.1 and a project derived from the...
