In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
What should be done if we add nRF51822 SDK into our code for business (redistribution)? We have our own IDE and would like to integrate "nRF5_SDK_11.0.0_89a8197" into our...
I wanna plan to design a new hardware which has ability to connect to smartphones using BLE and broadcasting ANT pages in the same time. I also need a way to transmit some...
Hello,
I read the Errata document infocenter.nordicsemi.com/.../nRF52832_Engineering_B_Errata_v1.2.pdf , and in the section "3.10 [62] NFCT: Can draw current when not enabled...
Hello,
I'm designing a new design and planning to use WLCSP version of nRF52832.
I have few questions about this since all reference designs are made with QFN48 version...
Hi every one,
I use the nRF51822 to read temperature from sensor and send it through UART, i follow the SDK examples and just change connection interval to 0.5 sec and...
Hi I am trying to get my 128x32 oled device working with my nrf52 development kit board. Using PCA10040. Does anyone have or know of any example code that can get it up and...
Hello,
I am writing some data to flash, but when it runs to storage_clear, I get the return code---0x10. It seems clear failed. And I tried storage_update, and it failed...
Hi, I'm working on a project, I want nRF51822 can get notification when android phone got a call or email, just like ANCS work with iPhone.
I tried ble_app_alert_notification...
Hello,
Apologies as I'm very new to C and I may be missing something obvious. I have an actual ble Heart Rate device which I wish to connect to my pca10028 (nrf51422_xxAC...
I am try to porting nRF51822 Beacon v1.0.1 F/W for PCA20006 to PCA10001.
I could change GPIO port setting for button and LED.
Now normal beacon mode work fine and success...
We appear to have discovered today that if you do this sequence
sd_power_gpregret_clr(0xFF);
sd_power_gpregret_set(0xA0);
sd_power_gpregret_set(0x0B);
GPREGRET will...
I'm trying to understand the general structure of .h files.
nrf.h contains an #ifdef for NRF52.
I cannot find a #define NRF52 anywhere.
Any help appreciated.
Thanks...
We have our nrf52 working well with our iOS app - almost everything we need is in place. One last item (haha) we've been struggling with is to get the nrf52 to advertise our...
Hi,
I'm connecting to a proximity sensor, IQS263 over TWI interface and having some weird problems.
I'm using the same code I used to connect with the Invensense MPU...
Hi.
We are trying to get nrf52 to work with 1.8v spi master. We are using level sifter with it. However when we connect the nrf52 to level sifter to spi output, the whole...