I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
when phone connect to the device, I print the connected address.
However, I find that the bluetooth address is not same with the phone bluetooth address.
here is the debug...
Hi,
I am trying to include temperature (read from DS18B20) in advertisement data using BLE_UUID_HEALTH_THERMOMETER_SERVICE. So far it works fine, but my temperature is...
Hey,
I am using twi_hw_master.c and twi_master.h libraries for twi and want to disable i2c to save power when not in use.
I use the following two lines to disable the i2c...
Hi,
i am using Eclipse 'Mars' and Segger V5.10c to debug some of the SDK examples. The Eclipse command line shows only binary garbage. How can I get the garbage readable...
Hi,I am using s130 softdevice and SDK9.0 .I add static passkey(123456)in my project base on ble_app_uart project and basic functions have been achieved.But I have a question...
Hello!
Is it fine to ready NRF_RADIO->FREQUENCY right after receipt of BLE_GAP_EVT_ADV_REPORT?
Does its value have a relationship with recent adv. report?
hello there when i am trying to open project C:\nRF51_SDK_8.1.0_b6ed55f\examples\ble_peripheral\ble_app_template - Copy\pca10028\s110\arm4. i am getting error like
Third...
Hi,
I have set connection interval as 1.8s.
But i have transmit data every 1 min.
I noticed that BLE transmits data every 1.8sec.
Can someone please tell me what is...
I have just exported a project from mbed, to the Keil uVision4 tool chain.
Create New Project "BLE_Thermometer" on mbed.
"BLE example for the Health-Thermometer...
I see in the information about the nRF51 talking about the support of 4.2. But it is not clear to me the extend of it. I am focus on the link layer and I would like to know...
Is it possible to implement 2 peripheral in one device (need to connect a peripheral device with two different centrals)? When should i expect for this feature?
I have a question about how much memory is required for app timers.
The comments for APP_TIMER_BUF_SIZE state that the buffer size must be one more than actually needed...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
