Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hello, I'm using nRF51822-mKIT for a research.
To verify ADC readings from analog input, I've connected P0_5 to GND and ran the following code:
uint16_t adc_result;...
For my project I would like to use this bluetooth module: freqchina.en.alibaba.com/.../Fingertip_size_nRF51822_Module_Ultra_Low_Power_Bluetooth_4_0_Low_Energy_RF_Module.html...
I am trying to connect to a peripheral through s120 central and vendor has a 128 bit fixed UUID
I am trying to add it on central using sd_ble_uuid_vs_add(...,...) but it...
I am trying to develop an application for the Android that will communicate via BLE to a Nordic device. I'm able to read the characteristic's value by
BluetoothGattCharacteristic...
I'm using nRF51822 SoC and I have a LIS3DSH accelerometer connected to the ship via SPI bus . I used the SPI master example . So i used the switch_state() function then took...
Hi, I would like to know how I can immediately detect when a connection link is loss either from the central or peripheral. I need to know which error or notification to look...
Hello.
Here was the question about S120+DFU and Petter Myhre said that Nordic ready to release the new S120 version with the peripheral mode support, so making DFU OTA will...
Today I tried to update the SoftDevice of my project. I was working with the experimental NUS example with the old S310 SD (1.0.0). Because I want to communicate thru ANT...
Hello everyone,
I'm developing a security scheme in which the firmware verifies that the nRF51822 is the same as the one in the factory to which the firmware was installed...
Hi -- Can I run direct test mode on the nRF51-DK?
I've found the Direct Test Mode window in nRFgo Studio, but my board isn't available in the "Set up on ... " pulldown...
Hi,
I'm trying to implement a device including a PWM counter and a high resolution timer working with softdevice stack 110. Per the examples I got from this site, I'm using...
Hello! I'm trying to use s130 as peripheral.
I flashed nrf51822 with s130 stack. Opened peripheral example and build it with .ld file for s130.
After it I flashed this project...
we have a 2 chip soln. nrf for Ble, Atmel for main application.
config data is located in the Atmel part. Config data also has BT Device name, ADDR, Adv Params etc.
I...
