I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
I want to make a nRF51822 as broadcaster and peripheral role concurrently. It should have continuous broadcasting advertisement data under accepting connect-requests to notify...
Hi,
Looking at pstorage related code, it appears that it handles data copy from RAM to Flash.
Can I use pstorage functions to move data within Flash? I want to implement...
HI All,
We want to use UART RXTO event to detect UART packet boundary.
So we propose to add one entry APP_UART_RXTO to app_uart_evt_type_t in upstream sdk to sync.
...
I can not understand how works READY register in SPI master:
after first byte transmission READY sets high, i set READY low and send second byte, but READY never sets high...
I can upgrade the firmware by MCP on air ,But there are one conditions:
reset the device while holding down the Enter Bootloader Mode button or a invalid application is present...
Hi,
I am running (and reconfiguring) ble_app_lbs (LED + Button BLE app) example as a kind of start off project for me. I am actually trying to figure out where I can control...
Hi,
When i increase the global buffer , i got this error.
if i reduce buffer size and add few more characteristic , i am getting same error.
How can i use Flash memory...
Hi All,
I started with example ble_app_multilink_central for S120 from sdk 6.1. I then started stripping the application to get a barebones central. I removed app_trace...
What I`m using:
-nRF51422 EK
-Keil v5
-nRFGo Studio 1.17.1
-SDK 6.0 and 6.1
-SoftDevice S110 v 7.1
-Applicatio: ble_app_hrs
I first Programm the SoftDevice
Softdevice...
I've done a lot of reading on the forums about this topic and done a lot of trying myself. I haven't had much luck and it seems like most everyone is in the same boat.
...
Hi,
On my ble application, I want to keep after wake up reset the previous value of a variable, I tried using sd_power_ramon_set(0x000f000f) to keep on all ram partitions...
It seems like a pretty large hardware/software release just came out and I am a little confused. Where can we find documentation about all the new hardware (nrf51822-QFAX...
Hi I try to run master control panel on PCA10024 development boad. On master control panel, I set File->Options->Serial port: "Show all serial ports". Then master control...
Hello,
I'm reading S210_SoftDevice_Specification_v2.0.pdf and there is written: "The ANT channel encryption engine provides the ability for a single channel..." does this...
I didn't find information about size of buffer within softdevice 310 for ANT messages.
I found that S310 requires: 128kB Flash, 9kB RAM, Stack 2kB
But how big size of...
