I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hello,
we made PCB based on reference with ST balun. In circuit the low freq crystal is optional, so we didnt use it. In software i noticed app_timer use RTC timer. So the...
I am trying to bootload an extremely large hex file using a slightly modified DFU (modified from SDK v5.2.0's example)
The problem is that the hex is so large that eventually...
Im having errors like Arduino is in the while(1) loop if I enable the DC/DC converter in the characteristics and generate service.h file , If I do not use this setting everything...
I have a NRF24L01 board, which acts as a receiver. It listens on RF channel 2 using address pipe 0 address as follows 0xC47B4D0331. I am able to transmit to this NRF24L01...
I need to wake my uC from sleep when the nrf8001 gets in connected mode and for that I need to supply an external interrupt on hardware interrupts on the MCU.
Will active...
www.dropbox.com/.../error.jpg
it is not even reach main()
same as devzone.nordicsemi.com/.../nrf51422-flashes-ok,-but-debugging-fails-stays-in-moves-r0,r0
is it related...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi
In my project, we wanna transmit large amount of data from UART master to nRF5182, and then to iOS7. Baud rate is 19200. Feed-in speed is near 2KB/sec. BTLE transmission...
I am trying to use this android app to read/write values from my nRF8002. Every few seconds I get a request to bind to the board, even if I already accepeted to bind to it...
I have a example using nRF24LE1.
So. I want know what can I change that example. or how to I get nRF24LU1+ example.
nRF24LE1 example is this.
/* Copyright (c) 2009...
Hi all!
I got a little problem with my ble device.
That is: my device takes system_off mode as initial mode, when being pressed the button, it will wake up and start advertising...
I am using UART0 for wired communication and S110 for Bluetooth LE communication at the same time, using HRM profile. System seems to work as expected, I get log output from...
I am using the nRF51822 to communicate with a HRM (and nothing else), but I intend to use the power of the ARM to control other sensors and process the received data. I use...
