Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Upon initial connection with iOS device, returned connection values at BLE_GAP_EVT_CONN_PARAM_UPDATE are:
ble_event: got BLE_GAP_EVT_CONNECTED. role: 1, conn_handle: 1,...
Hello,
I using the Segger with the last SDK. I modified the ble_app_uart example, I added the softdevice to the addition files. When I run the debugger everything seems...
Hey guys, Recently i decided to get the ICM-20948 DK and exploring it. I read all the info on their site and all their guides but the only briefly get over the topic, so i...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I was going to “Batter Service”. Battery level...
Hello, I am using the PCA10056 to program a nrf52811 chip on a custom board with SDK 15.3.0. I'm using the example ble_app_blinky_pca10056_s140 I am following the steps in...
I am working on transferring BMI160 sample given in zephyr samples (\ncs\zephyr\samples\sensor\bmi160) to nrf sample (\ncs\nrf\samples\nrf9160\bmi160).
Below is the changed...
I'm having a problem with the nRF52 SAADC. It's configured for
One shot operation on Channel 0 using pin Ain4.
Gain of 1/6
Tacq set to 40us
8 bit resolution...
HI,
I want to configure HT1632 LED driver using SPI communication protocol
for that i should send commands LSB to MSB
immediately data should go MSB to LSB
My question...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’ and “nRF Connect” app.
I am trying to understand...
Hi all
SDK 11.0.0 S132 version 2.0.1 nrf52832
I want to turn on the PWM and turn off the PWM after 1 minute. The device will do BLE advertising When the device wakeup...
Hi,
I have read a lot of posts about using the internal LDO/DCDC converters or using an external switch mode regulator, but haven't seen any answers I could use.
I have...
I am looking for guidance on how to fragment data in Extended advertisement on the nRF52840. I am using the "ble_app_rscs" example to advertise in non-scannable non-connectable...
Hi ,
I need to update the NRF52832 with another different module.
I can update without problem by using the nrf connect app.
I would like to use another device without...
Hi,
I am trying to get event messages on the terminal from a Generic On Off (GOO) Client node. I have the provisioned the mesh using the pyAci through another board running...
Hi,
I am using nRF52840 Preview DK, with SDK V15.3.0 and Softdevice API V6.1.1
First, I modified the 'ble blinky peripheral example' to have more characteristics tying...
