Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
I've tried this but it does not work: static void adv_slots_init(void)
{
uint8_t default_frame_data[] = {0x03,0x03,0xAA, 0xFE,0x13,0x16,0xAA, 0xFE,0x10, 0xF8,0x03,'g','o...
on the nrf52832 I am configuring pin 10 as an input. There is either 0 or 3.1V on the pin depending on whether a charger is connected to the board.
When I read the state...
Just stumbled upon this:
#define TIMER_PRESCALER_PRESCALER_Msk (0xFUL << TIMER_PRESCALER_PRESCALER_Pos) /*!< Bit mask of PRESCALER field. */
Should be
#define TIMER_PRESCALER_PRESCALER_Msk...
I am working on project where I am storing and reading data from an SD card. During the initialization, I would like to print the full contents of the root directory - "/...
Hello,
I have a problem through which unfortunately I'm not able to come across alone. I'm using nRF52832 with softdevice and UART central example from SDK14.2 (..\examples...
I'm using nRF52840-PDK. I created a custom ble service following this tutorial ( github.com/.../custom_ble_service_example) and sent my sensor data over bluetooth. Now I'm...
Hi ,
I am trying to disconnect a connected central (phone) by calling sd_ble_gap_disconnect from my nrf52 configured in multiperipheral mode. . The disconnect call returns...
I am trying to time a capacitor discharge through different resistance sensors for greater resolution than an ADC. I did this using the GPIO functions initially but the SD...
Hi,
Is it possible to use Segger Embedded Studio with nRF51?
I see on your web site it's supported with SDK 14 or greater but this SDK is only for nRF52.
My product...
I have problems with my custom board.
I developed the firmware with the nrf52840-PDK and there the firmware runs standalone (with RTT connected and without) or when debugged...
Hello
I am working on nrf52382,sdk11,softdevice 2.0.
/cfs-file/__key/support-attachments/beef5d1b77644c448dabff31668f3a47-fd3fce63fa6d4ddfa73158194e4d87c3/battery_5F00_pins...
Hello,
I am writting a batch script to flash a PCA10056.I use it to flash the softdevice, the bootloader and my application.
The script works well and flash the device...
Here NRF52 TX pin is connected to Battery to measure voltage Level. i am using NRF52 with SDK 11 and s132 soft device.
Here is my Schematics
here BATTERY is connected...
