Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Why is the event length of the BLE Central HRS demo set to such a high value of 320*1.25ms = 400ms?
The demo seems to work ok with the BLE Peripheral HRS demo using the...
Does the Battery Service Client (ble_bas_c) module handle subscribing to notifications from multiple slaves? In my use case, I have the nRF52840 dev kit connecting to multiple...
I need to keep track of time on a device featuring the nRF52 and have an RTC run continuously in the background. The drift should not be more than a few seconds over a year...
Hello I try to use P0.09 as GPIO with this simple code but not working. (Works well with pin P0.08)
#include <stdbool.h>
#include <stdint.h>
#include "nrf_delay.h"
#include...
Hello,
I use the bootloader from the SDK SoftDevice 14.0.0.
I use the Laird module BL652 which have a nRF52832 component without external clock.
To compile the bootloader...
Hello Everyone,
I am working on nRF5 14.1.0 SDK, My question is how to generate "ble_app_buttonless_dfu_without_bonds_s132.zip" dfu file.
Can any one tell me the exact...
I am using nrf52832_xxaa and SDK 14.2.0.
Does app timer play a role in power optimization?
If yes, Can reducing the app_timer frequency reduce the power consumed by the...
Is there a BLE mesh SDK for nRF52840, and if yes is there anybody tested it? I'm going to switch to the nRF52840 from nRF52832 and it is very important for me to know it is...
Fanstel BT832 module mesh client stuck in nrf_mesh_sdk.c, 187, Initializing softdevice. When I upload the code on the NRF52 DK It works, but when I upload with segger embedded...
I have set up an environment to upload data to the nrfcloud using nrfconnect and the nrf52 dk.I can only upload data upto ff and then it resets to zero .The value which i...
Hello,
I`m searching for a possibility to detect a possible Flash corruption caused by a Brown out or something else? Is there any controller interal possibility to detect...
hello all
This is one of the point that causes me problems into my migration: I figured out the new logs and the SD obbervers... now this:
the 52832 advertises correctly...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Dear.
In my project using twi function(nrf_drv_twi_tx, nrf_drv_twi_rx).
I am faced with parameter problem that length(uintt_t) of nrf_drv_twi_tx function.
I want...
