Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hello,
I am using SDK 14 & nRF52832 & peripheral role; I have setup a timeout in the order of several seconds, and during this time my device shall advertise but reject...
Hi,
I'm using nrf52840 and trying to define the pin mappings for my custom board. In order to do this I'm studying the board definition of pca10056 (pca10056.h).
In...
Hey all, I'm trying to run the node cli flash "imei" -f /path/to/firmware.hex command on the terminal. It prompts as ERROR flash <deviceId> failed!,
ERROR Error: No such...
Hi
I'm working with version v8.6.90 since the master version at this date have an Auth amplify issue.
The Fetch function on the map is buggy :
Here is the Chrome dev...
We are using nRF52 SDK 17.0.2 s132_nrf52_7.2.0_softdevice.hex in our application. When entering in DFU mode from application, we perform nrf_power_gpregret_set(BOOTLOADER_DFU_START...
I am willing to use nRF52832 chip in one of my project. But all the breakouts dont fit the size and I want to design my own PCB with i2C accelerometer. I only want to transmit...
Hi,
Corect me if I'm wrong, but the initiation of ble_gap_addr_t.addr_type in main.c in the HRS_C demo is not necessary, as the addr_type is calculated based on the address...
Hello Folks,
I am following below steps to add Zigbee FOTA to Zigbee: Light switch example.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_zigbee_configuring_libraries...
Another problem is that when I turn on I2S to read data, the while loop does nothing, and the broadcast can't be transmitted, just like I2S has occupied all the CPU, and other...
Hi Devzone,
I use original mqtt_simple example to test connecting with MQTT Broker.
I ran it on Ubuntu, SDK v1.5.99. When I press button to publish message, some errors...
I'm planning to evaluate AoA and AoD using nRF5340 DK. I asked my local RSM about getting the antenna array and was advised to get nRF9160 DK.
After reading the documentation...
I have a sniffer working . I Have a bouad with
west build -b nrf9160dk_nrf9160 .. If I start an example on the zephyr-mainline hello it work I see in ttyACM0 the printk...
I am running the usbd_msc example in nRF5 SDK 15.2 and trying to eject the disk on Windows/macOS.
But, USB MSC drive sign kept being visible in my explorer. Is there any...
Hi
I'm using nRF Connect SDK v1.5.1 and Segger IDE. Starting from fresh with Clean Build Directory, the sample won't compile with Segger IDE (build solution).
I aware...
With SDK15.3, s140 softdevice, NRF52840 (InsightSIP ISP1807)
If I use SAADC with 2 channels then I see a 0.7mA sleep current after the call to nrfx_saadc_sample()
...
