I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
I am currently working on a project with a nRF9160 and in the very early stages of evaluation.
I have a few, hope not too many questions that I hope can be answered here...
I have been struggling to get the DFU in our own application to work. When starting a DFU from the desktop nRF Connect 3.4.1 it reports an error:
According to the log...
Hi,
We are using nrf52840 development board and segger embedded studio. I am using thread concept here to run another function in parallel to my main function. i want to...
Device: nRF52840, nRF5 SDK16.0, Softdevice: S340 (ANT_s340_nrf52840_6.1.1)
Hello,
As next step to increase usability of our product and adding new features, we have...
I hope someone is able to answer a few question.
I read quite a lot but still some things are still confusing.
If we use e.g. the AMB2621 Module of Würth, is skipping...
Hi,
I am trying learn about IO/ events that can wake-up nRF52833 from lowest power mode.
What qualifies as event that can serve as wake-up source?
Is it possible to...
Dear sir,
Got error while uploading .zip in DfuTarg as "SD version failure". I'm using nRF52840 DK board. I have tried to create .zip by --sd -req 0xB6/0XAE/0xA9. zip get...
I'm curious what the modem does if, upon waking up to service the PSM interval, it fails to connect? Does it go back to "idle" and try again on the next PSM interval or does...
Guys, In a Mesh project, when setting up flash manager:
How do you get the right value of flash_manager_config_t.p_area ?
And where and how is it configured?
Thanks...
Hi ,
I wirte a python script to download FW to nRF52832 custom board, the FW is the merged file with softdevice（s132_nrf52_7.0.1_softdevice.hex）, bootload, bootload settings...
The version used is nrf5_SDK_for_Mesh_v5.0.0_src.
nrf5_SDK_for_Mesh_v5.0.0_src\examples\light_switch\server.
Question 1: I want to turn off mesh broadcasting first,...
Hi
data sheet of the nRF52840 states that the QSPI port pins should be initialized to "high drive".
I've experimented a little bit because I have problems with a Macronix...
I have connected a BM680 sensor on a BL654 (NRF52840) via I2C. I have connected the power to the BME680 on a switchable power rail. I need to power this rail with a GPIO pin...
I am trying to create a test case for in house validation and would like to know how to do so.
Here is what I want to do:
I want to create a boot loader that checks...
Hello,
In nRF5_SDK_17/examples/dfu/secure_bootloader/main.c, the main program starts off with protecting a couple of flash areas:
But how can, after this, an OTA update...
