At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello,
Our application runs over nRF52840 + SDK16 + FreeRTOS and we are using libuarte application to drive the UART. We found that the app_timer_freertos.c doesn't provide...
Hello ,
When i am using sdk functions with freertos some of the callbacks/functions requires (for example) xTaskNotifyFromISR() instead of xTaskNotify .
So how can i decide...
I am going to mass-produce beacons with built-in ble uart app sample.
However, I am not sure those produced beacons will have unique mac-address.
In my view, those are...
Hi all i am trying make a communication between esp32 and nrf52840 using UART. Initializing the uart driver was proper and pins also correct. when nrf start transmits then...
Using nrf52810 SDK 17 ble_app_hrs for my example, and i add some code about the passkey
Now the situation is after I enter the passkey on my Iphone nRFconnect app, and if...
As with my recent inquiry about a softdevice assert at PC=0x24e70 , I'd like to know which assertion fails in softdevice S132 version 7.0.1 at PC=0x157ec.
Is there a table...
Hello,
I observed a weird behavior when I changed to nRF52840-DK from nRF52840 Dongle. I am using the device as an SPI slave connected to a Raspberry PI as SPI master. ...
While trying to execute the light switch example, i was able to set the nrf52840 as evaluation board as proxy server but failed to do the same with the dongle.
2)When...
Hi,
When running the at_client example, I send the AT+CFUN=1 command via the LTE link monitor. After a few seconds, the nrf9160 reboots.
I want to say that before my program...
Hi all,
Currently I am working on my first project with the nrf52832. All is going quite well, but I would really like some help with my flash layout, basically I got some...
I'm attempting to control the microphone level from Windows 10 and Mac OS by configuring a Feature Unit.
The USB audio example demonstrates how to configure a feature unit...
Hi,
I am using the uart example from https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/uart/src/main.c
I want to read serial data from...
I'm making my own protocol on nRF52832 devices and I'm wondering if there's any possibility to have data corruption when CRCSTATUS contains CRCOK value.
I'd like to get...
hi all,
I am using the following example:
"..\nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_uart_adc_scan_mode" to send via bluetooth data coming from ADC. ...
Hello, team.
Thank you for helping.
I was wondering that what is the difference between 'managed flooding' and 'relaying' in mesh.
The only one that I know is provisioning...
