I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hello everyone,
As we know the proxy protocol is defined to include BLE devices in a mesh network. But as per my understanding there has to be made some changes in the...
Hello,
I am using nRF52840 PCA10056 DK i want to make my board as central device and scan for all nearby ble devices and display it's device id on terminal connected via...
Using SCAN_INTERVAL and SCAN_WINDOW at 1600 vill make the flash write and erase come out with a error, the fstorage is working fine before the SD is initialised.
/** @brief...
Hi,
I am using the secure bootloader as a template and I want to use the inactivity timeout to shutdown after 10 minutes.
I saw that the limit should be 60000000 ms (according...
SDK: nRF5 SDK for Thread and Zigbee 1.0.0
I have code for the SAADC based on the Low Power SAADC example here .
I have modified it to sample 4 inputs, and changed the...
Hi,
I would like to check battery level using the SAADC of the nrf52840.
Assuming the voltage is less than 3.6V, do I need to have a resistor between the battery and the...
HI,
I am new to IoS development with NRF.
I am having NRF52840 DK, IoS device. I want to implement USB HID device application (similar to pulse/Gluco meter ) on IOS. I...
Hi,
I am not able to compile the SDK example by using SES for ARM V3.52.
I got one error which shown below:
It pointed to the link ldr r0, =%4
Thanks
Gan
Hi,
I am using fatfs of nRF5_SDK_15.0.0_a53641a.
I am writing a program with keil.
I am currently doing SPI communication with BLENanov2(nRF52832) and SD card with...
Hi,
I am implementing the UART on NRF52840. TX works but the RX doesnot. While debugging, I noticed that STARTRX task register is not getting set due to which the RXDRDY...
Hi Sir
We'd want to do RX testing with DTM mode, however, the dtm example code looks can't report receive data or total packets counts,
So that, we don't know how to determine...
Hello,
I'm using the nrf15822 chip and am using the ble_app_uart example from nrf5_sdk_12.2.0.
I know softdevice will automatically generate random numbers through RNG...
I've been told due to PAN 58 it is not possible to use EASY DMA with nrf52832 without switching to the deprecated SPI driver. Is there a workaround that allows the use of...
Hello,
We are going start custom PCB design by using nRF52840 chip and SDK 15.0, but confused for use 3rd party nRF52840 modules or design complete custom PCB using componenets...
