Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Setting up an example of the problem
As I promised in this thread , I have been testing out the ADC on the nRF51822 and trying to see how quickly I can sample per minute...
I'm using FDS in SDK 11.0.0 on a nRF52832. I was having some trouble with freeing flash storage and after doing some research I came across this post and I applied this patch...
Hello,
There is a bug in pstorage.c from SDK which can cause that module to fail to complete a flash operation. The problem is that the pstorage_sys_evt_handler function...
The product spec says "This event will also be generated if the supply voltage is already below VPOF at the time the POF is enabled" but it seems like the event is not generated...
I have a BLE device that is using Nordic SDK 8.1 and uses PWM to control an LED. Now I want to turn the led off with PWM. To do this I set the duty cycle to 0 and printed...
Hi,
I'm working on nrf51822 with soft device s130. I'm trying to send a data packets from the nRF51822 over BLE to an android device.
I want to know how much data...
Hi!
I try to create a custom service. To do that I copied the ble_bas service and followed this guide.
You can see my init function here:
#define APP_UUID {{ 0xC0...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 as central and peripheral.
Q1. What's "sd_ble_uuid_vs_add" function? is it for setting service UUID?
Q2. If Q1 yes, how to change...
I was reading a review of this product from a 3th party and they was claiming that a disadvantage about using this chip is that "Some peripherals and resources are not available...
SDK: 13.0.0.0-1.alpha
example ： ble_app_hrs_freertos
I am developing a product, referring to the “ble_app_hrs_freertos” example, when I tested my functions found a serious...
I've just tried to update the mbed firmware on an nRF52-DK to version 0219, and have hit some problems. Firstly, after dragging the .bin file into the Bootloader drive, my...
I've had a sequene of problems attempting to install the power profiler software on my Lenovo T420 Win7 64 bit machine.
First Issue
When attempting to run the python_packages...
I would like to pick up audio signal with a microphone for ex. AKU340, then use audio codec to digitize it, then save the output in a SD card connected to the nrf52, reading...
Hi there! I am a beginner of bluetooth technology.
We try to build a kind of IoT based on bluetooth mesh nodes with nRF51822. According to the instruction of nRF Connect...
