Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
For my project to simulate the spreading of a disease I am thinking of recording the complete social network on the beacons and then collecting the data to a pc. I have roughly...
I am using nRF51-DK hardware and working on the ble_uart_app s130 SDK_11
Upon power-up, nRF51 is discoverable and connectable. After sometime, it is no longer discoverable...
Hi, I am using microESB library. We want to test the continuous carrier wave mode for ESB(similar to using DTM for BLE continuous carrier wave mode). Is there any library...
Hi,
I have the nrf52 working perfectly in iBeacon mode. Even when my iPhone is Off, the iPhone will wake up and post a notification with UUID, Major,Minor etc.. It's great...
I have suspended my Beacon in SLEEP (at .5 uA) until a keypress. Is there an event that can trigger an event if there is a low voltage detection while in SLEEP?
My goal...
hello,
I am trying to write one characteristics on GATT server from a client. My server program (acts as peripheral) is working fine with MCP. But when i am trying to connect...
Hi,
I've spent the last few days trying to get this going and getting super frustrated.
After having no luck getting the nrfutil to work on Python ( another thread ...
HI,
I am using micro esb(0db tx power, 250kbps, RX mode) from GitHub( github.com/.../nrf51-micro-esb) . I am using nrf51822xxaa and SD10.0 and s130. With just the micro esb...
I can't get the Master Control Panel to work. I think the drivers might be messed up but various re-installs aren't having any success.
Can you suggest some troubleshooting...
I'm Dinesh Katkar, trying to adapt
new IoT design and development and planning to build wearable device based on nRF52832 Bluetooth SoC chip and ordered nRF52 Development...
Hello,
I am new to all this RF stuff. I am trying to set up multiple transmitters (2 for now) and one receiver. Basically, each of two transmitters read one set of data ...
hi all,
i am currently using version 8 sdk.
i tried to include bsp_init() function in my code.
i attached following header files
#include "nrf51.h"
#include <stdbool...
When exporting the example project BLE_HeartRate from the online IDE to the GCC (ARM Embedded) toolchain, the makefile fails to compile.
First, the compiler throws "fatal...
Hi:
I am using nRF51 Dongle to develop my platform, and software is base on esb_low_power_prx and esb_low_power_ptx in nRF5_SDK_V11.
For production, I need to program...
When I connect to another beacon using sd_ble_gap_connect() scanning on my device is stopped. I have to wait till connection is established or establishing connection fails...
