Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I read the discussion in the following link, but my application is different so I want to ask for advice on how to proceed.
https://devzone.nordicsemi.com/f/nordic-q-a/50642...
Hi all,
I successfully flashed the peripheral_hr sample from the Getting Started guide into my nRF5340 PDK (from here: https://infocenter.nordicsemi.com/index.jsp?topic...
Hi,
I am new to the SAADC concept in nrf52. I have to measure the battery voltage using SAADC over ANI0 pin. I using battery with voltage 4.1 volt.
This voltage is divided...
Hi nordic,
In our project we are using pairing and bonding process. the first pairing with the iphone was successful, I delete the NRF52832 pairing infomation,iphone pairing...
Hello ...
Our product (nRF52810, SDK 15.3.0, SD 112 6.1.1) allows the user to change the device name, which typically happens once when new product is received. Our app...
I am running the ADC demo for the 52833-DK (pca10100) and can’t seem to get any valid readings. SDK 16.0: examples\peripheral\saadc
I am applying 1.5V to AIN0 on P8 and...
Hi, I am developing something using Zephyr on a nRF52840-DK as one Bluetooth mesh node and a Thingy as the other. To program the Thingy, I have it connected the Thingy to...
Hello -
I am trying to run the USB CDC ACM example on macOS 10.12.6. Following the instructions in the example app, I should see a virtual COM port as /dev/ttyACMx when...
Hello,
I am doing some testing on the nrf52832 DK using the mesh light switch example, i am sending ACK messages, i would like to log the time it takes the message to reach...
Hi,
What is the proper way to set "real time" in nRF9160 with nRF Connect SDK?
I want the function time() from the file time.h to return the correct time.
I know that...
I am using SDK15.3.0 and softdevice 6.1.1 on a nrf52DK.
I have a binary (compiled contiki application) that works when I flash it using nRF Connect. It is flashed from address...
Hi,
I have a PCA10040 board (nRF52-DK) which has a P20 debug out interface. I've got another nRF52832 breakout board which has VCC/SWIO/SWCLK/GND wires for debug/programming...
Hey,
I configured one device as low power node in mesh network.
With the button press interrupt low power node wakes up and perform some operation (publish BLE message...
Dear Nordic
I am using SDK14.2, I cannot pint info . SDK periphral uart and serial can't print also
nus example jlinkrtt print as below:
<00> warning> nrf_sdh_ble: RAM...
Hi,
I am using pc-ble-driver version 4.1.1 with the SD version 6.1.1.
I want to configure the TX power for the NRF52 USB dongle.
Do you have a code example for configuring...
