I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hi,
I have some troubles using TWI easy DMA. I set EASY_DMA flag to 1, but I can't see any results in my performance tests. Can anyone explain me the required steps? ...
I am looking at the android version of the Blinky application and was trying to make some modifications to enable the LED3 on multiple boards (peripherals) to turn on from...
Hi,
In a peripheral, a notification is sent to the central every 10ms. (payload less than 20 bytes)
I use : radio_notification_init(6,NRF_RADIO_NOTIFICATION_TYPE_INT_ON_ACTIVE...
i want to read the temperature ..... my temperature data is executing from 0 degree temperature ...is there any way to execute only actual data instead of starting from 0...
I'm probably not using the good terminology here... let me explain my application.
I have an existing board which has all the logic implemented in an STM32 MCU. I now need...
Using Softdevice 132 version 6.1.0 I issue the request for scanning by calling sd_ble_gap_scan_start() with: ble_gap_scan_params_t scan_params = { { .extended = 0, .report_incomplete_evts...
Hi all,
I want to measure higher frequency (8 MHz) count/ticks by using the lower frequency (32 KHz) is there is any method to do it or any examples.
I want to measure...
Hi,
I am evaluating the nRF52840 with the Segger IDE.
I am about to experiment with Bluetooth, but I have a hard time understanding the different protocols/softdevices...
Hi, recently I've been confronted with this issue that all of my stocked nRF52832 ICs would not work with the lastest SDK, which later turned out to be engineering samples...
In the light of recent news like this one, https://arstechnica.com/information-technology/2018/11/bluetooth-bugs-bite-millions-of-wi-fi-aps-from-cisco-meraki-and-aruba/ ,...
if m_replay_cache[ivi][i].seqno == 0xFFFFFF, then new message received and seqno == 0 or other value, Whether the message is valid ?
Because the seqno of the new message...
Hi,
We have many projects based on nRF52832 SDK 12 and we are porting them to nRF52840 SDK15.2 to take advantage of the new BLE5 features.
The problem is that we are having...
In my nRF51822 I have an app & a dfu bootloader (modified from nRF51DK) & softdevice .
The app starts the watchdog with 5 seconds timeout. An user can make the app to...
Dear Sir
We will like to disable the BLE advertising data whitening, could you advise us how to disable it?
We have tried to modify the following 0x1UL to 0x0UL and looks...
Hi Sir, I am use Laird BL651 module, which use nRF52810. I am use nRF52 DK debug output (P19 and P20) connect to our board, but the nRFgo studio not able to detect device...
