Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
The data sheet recommends that both the TWI clock and data lines use pull ups and the GPIOs should be set to S0D1, essentially open collector drive. I can see the need for...
When trying to follow this guide for testing bluetooth mesh on a nRF51 dev-board Cmake returns this error:
../build $ cmake ..
CMake Error at CMakeLists.txt:16 (include_directories...
Hello, I have had luck in Keil making two NRF52 connect with NUS, central and peripheral. My goal is to have one central speak to multiple peripheral at same time via a piconet...
Hi
I have just baught some nRF52840 DK boards,
and I can test the BLE throught between those nRF52840 DK boards successfully.
This indeed help us a lot about research...
Hi,
I am using SDK 12.2.0 with my custom board. As per the my requirement, i need to ground or set logic 0 of my gpio pin no. 12.
So, how can i do this?
good morning to all
I wanted to ask if anyone has a design of nrf51822 where an external temperature sensor is used, to know how the connection to the chip is. Should I buy...
Hello,
I am learning about the behavior of "Notify" transmition.
From some web sites including below, I understood as follows.
devzone.nordicsemi.com/.../
So could...
Hi,
I am new to arm and ble development. I am used to work with AVR mcus and I am trying to migrate a project from AVR to nrf52.
AVR usually has some "General Purpose...
I'm transmitting data packets each of 48 bytes in the form of notifications using Bluetooth 5.0. When I observed the logs over sniffer, I see that the packets are fragmented...
Hi,
iam new to all this and hardly find answers for my question:
Is it possible to pair a nRF51422 with an Ant+ remote especially Bontrager TransmitR and use those remote...
nRF52832
Hi,
I am a little confused as to what component uses ble_flash (...drivers_nrf\ble_flash\ble_flash.h/c) and why? What is the difference between this and SD...
Hello all,
I've ported the buttonless DFU example to my project without the buttons or the LEDs, but I only tested the bootloader and not the uploading capabilities with...
I want to know the details of "DTM testing using nRFgo Studio".
On page 52 of "User Guide v1.4 of nRF51822 Development Kit" says, "For details on how to use the Direct Test...
Hi.
I bought the nrf51822 kit, and I have questions to ask.
I know that there are many sample code provided by nordic.
I know that the sample code will run...
Hi!
I am working with an application were two nRF52832 shall communicate over UART in half-duplex 1-wire mode (similar to what is described here but I use different pins...
