Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
I'm testing connection time.
I made structure as your sample code as below.
static const ble_gap_conn_params_t m_connection_param...
I am using nRF52 SOC.
I would like to use BLE to transfer files between BLE client and server. I was hoping to find an example of the OTS implemented in the SDK but couldn...
I opened, compiled, and uploaded the UART example on my nRF52-DK board using KEIL IDE. I use either CoolTerm or RealTerm on my PC. When I open the Terminal program I can see...
I Just upgraded my RTE to the latest two minutes ago, and tried an RTX example.
The example compiled OK, But in RTE manager, it is showing missing component.
Screenshot...
Hello!
I'm in doubts about proper configuration of GPIO pin, which I'd like to be able to reset external device (DWM1000), connected to nRF51 by SPI.
The datasheet says...
Hello,
I’m working on my own custom board based on the nrf52832 (QFAABB).
Here the schematic:
I succeed to flash the board with the nrf52DK (PCA10036) via the debug...
Hi there - new to Bluetooth but have an interesting question.
Is there a way to have multiple users connected to the same Bluetooth connection to stream music? For instance...
Hi community,
I am working on IoT device. We want to establish a secure connection therefore we are going to need a secure storage for our private key. I am aware that the...
Worked fine until yesterday. Board turned off with computer, also the power switch on the board was in off position before turned on this morning. Now the debugger circuit...
Hello Nordic Team,
Please, I would like to ask some questions about BLE based smart-phone accessory.
Actually, I think about using a BLE based accessory (for instance...
Tuning the nRF24xx matching network:
The balun-function is done by the
180° degrees phase shift in L1. This
causes the signals from the two ANT
pins, 180° out of...
I am sending IMU data as 20 byte packets through nus service at the rate of 50 such packets per second. The device is a nrf51 DK configured as ble peripheral (S110). The application...
Hi all,
I have a makefile which runs perfectly from the command line on Windows under GCC, but in Eclipse it fails with this message in the Console:
make flash
make...
My application had a ID to separate difference device & host for the communication in the same area. When the Host power up, it need to search any existing same ID Host nearby...
Hi ,
I want to set the channels used for exchanging DATA (after connection) when peripheral and master are connected.
i searched and i find that it's like this :
//Set...
