Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I am using the nRF8001 and trying to do ANCS. After rebooting the Arduino / BLE Shield, I have to reset Bluetooth in iOS in order for ANCS to work again.
I was thinking...
This is the second part of the problem firstly exposed in this question .
I have the problem that, with a Blend Micro Arduino board from Red Bear Lab after a while (randomly...
Hi,
I want to implement BLE based access control application. I have developed nRF51822 based Peripheral device & iOS application based central device to pair with the...
I've finally completed a BLE transmission using tips about connection interval, slave latency and supervision timeout given here . I checked it with Master Control Panel app...
We are trying out nRF51822. My colleague has a top of the line Lenovo running Ubuntu and is able to detect the module when scanned. However, my macbook pro Mid 2014 (Which...
I asked this question ( devzone.nordicsemi.com/.../) to get an answer that I needed to apply for getting the Apple iBeacon certification.
Now I applied for Apple iBeacon...
I'm wondering (hoping) if there is something that I'm not doing correctly ...
We have a BLE application on the nRF51822 which has been working nicely.
It is a custom BLE...
What might be the reason that sd_softdevice_is_enabled fails? I've been programming with the S130 for some time now. And now I am in the process of adapting the bootloader...
For the S310 stack the bootloader does not set a SD_MBR_COMMAND_INIT_SD command. What needs to be done for the S130 ?
#ifndef S310_STACK
sd_mbr_command_t com = {SD_MBR_COMMAND_INIT_SD...
[PLEASE READ THE EDIT FIRST]
So, first of all, I am new to bluethoot development and I am not 100% familiar with all the inner workings of the protocol.
I am trying...
I have looked over the entire site and can not figure out what is needed to change the Smart Beacon Kit firmware and uploaded it to the beacon.
Is there a way to recompile...
Hello ,
I'm working since few days on nRF51 dongle with SofDevice S310 and most things seem to be ok.
But when I follow the System OFF and wake-up sample supplyed on GitHub...
The v3 nrf51822 and nrf51422 power efficiency was improved.
What were the improvements? How much effect should we expect to see in various operating modes. System OFF,...
In the Nordic code at this github example
there is a reference to UICR.CLEN0 .
#define CODE_REGION_1_START 0x00020000 \\
/**< This field should correspond to the size...
