Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi
In my project, we wanna transmit large amount of data from UART master to nRF5182, and then to iOS7. Baud rate is 19200. Feed-in speed is near 2KB/sec. BTLE transmission...
I am trying to use this android app to read/write values from my nRF8002. Every few seconds I get a request to bind to the board, even if I already accepeted to bind to it...
I have a example using nRF24LE1.
So. I want know what can I change that example. or how to I get nRF24LU1+ example.
nRF24LE1 example is this.
/* Copyright (c) 2009...
Hi all!
I got a little problem with my ble device.
That is: my device takes system_off mode as initial mode, when being pressed the button, it will wake up and start advertising...
I am using UART0 for wired communication and S110 for Bluetooth LE communication at the same time, using HRM profile. System seems to work as expected, I get log output from...
I am using the nRF51822 to communicate with a HRM (and nothing else), but I intend to use the power of the ARM to control other sensors and process the received data. I use...
Mother board :6310
IAR: IAR Embedded workbench for ARM: 7.10.1.6735
IAR Embedded Workbench common components 7.0.2.3053
Softdevice: S110_nrf51822_6.0.0
sample Project...
I am able to debug in windows using uVision, and now I port it to use eclipse in mac,
however, I am getting GDBServer will be closed error, anything clue what did I do wrong...
Hi,
I am using Nrf51822 custom board.
i want to store Nordic temperature value for every 15 minutes .
i dont want to use polling method.
Kindly suggest me how...
Hey folks,
I am currently trying to use my nrf51822 evaluation board as a beacon. This is working pretty well but I need to have it broadcast its current battery level...
Hi,
I am using the following security level for my nRF5188 device.
BLE_GAP_CONN_SEC_MODE_SET_ENC_WITH_MITM(&bas_init.battery_level_char_attr_md.cccd_write_perm);
BLE_GAP_CONN_SEC_MODE_SET_OPEN...
I'm interested in minimizing footprint as much as possible for a project -- has anyone here used chip antennas with the nRF51822 that they can recommend?
The fractus chip...
I have taken your advice to use the nRF51822 for my current design commission, but a number of downloadable files are locked. How can I get access to them?
Hi
I have a module of nrf 8001 and i am successfully communicating with nrf 8001 low energy bluetooth chip. I want to know is there any security feature defined in the...
